Exmark Lazer Z CT manual Service Interval After First 100 hrs Then 500 hrs thereafter

Page 34

b)Locate filter under left rear corner of engine deck.

c)Carefully clean area around filter. It is important that no dirt or contamination enter hydraulic system.

d)Unscrew filter to remove and allow oil to drain from reservoir.

IMPORTANT: Before reinstalling new filter, fill it with Mobil 1 15W-50 and apply a thin coat of oil on the surface of the rubber seal.

Turn the filter clockwise until rubber seal contacts the filter adapter then tighten the filter an additional 2/3 to 3/4 turn.

e)Fill reservoir as stated in Section 4.1.10.

f)Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

g)Start engine and move throttle control ahead to full throttle position. Move the speed control levers to the full speed and run for several minutes. Shut down machine and recheck oil level.

Do not change hydraulic system oil (except for what can be drained when changing filter), unless it is felt the oil has been contaminated or been extremely hot.

Changing oil unnecessarily could damage hydraulic system by introducing contaminates into the system.

4.1.25Wheel hub - slotted nut torque specification

Service Interval: After First 100 hrs.

Then 500 hrs thereafter

When tightening the slotted nut on the wheel motor tapered shaft:

a)Torque the slotted nut to 125 ft. lbs (169 N-M).

b)Check distance from bottom of slot in nut to inside edge of hole. Two threads (0.1”) or less should be showing.

c)If more than two threads (0.1”) are showing remove nut and install washer (PN 1-523157) between hub and nut.

d)Torque the slotted nut to 125 ft. lbs (169 N-M)

e)Then tighten the nut until the next set of slots line up with the cross hole in the shaft.

f)Replace cotter pin.

Note: Do not use antiseize on the wheel hub.

4.1.26Fuel Tank – mounting hardware specification.

When installing the nuts onto the fuel tank studs, fully tighten the nyloc nut and back off 1/2 turn. This allows for normal fuel tank expansion and contraction with changes in temperature and fuel levels.

4.1.27Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type” are used on the following fasteners:

a)Pump drive sheave setscrews.

b)Square head setscrews on hydro pump control arms.

c)Clutch retaining bolt in the end of engine crankshaft.

d)Caster wheel spacer nuts.

e)Fuel tank bulk head fitting nuts.

f)Cutter housing spindle nut

29

Page 33 Page 35
Image 34
Page 33 Page 35
Contents For Serial Nos 670,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Potential Hazard There is no rollover protection when the roll bar is down Page Maintenance and Storage Safety Signs Page Page Specifications Tires and Wheels Hydrostatic Ground Drive SystemCutting Deck Torque Requirements DimensionsOperation Instructions ControlsPotential Hazard Push the lever forward and down to disengage the brake PRE-START MowingEngaging PTO Transporting Potential Hazard Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Daily or more often in dry conditions Service Interval MonthlyService Interval Daily Check safety interlock system Service Interval 40 hr Service Interval 40 hrs Lubrication ChartService Interval Refer to chart Service Interval Once Yearly Service Interval 160 hrsService Interval As Required Service Interval 80 hrsService Interval After First 250 hrs Then yearly thereafter Service Interval After First 100 hrs Then 500 hrs thereafter Adjustments Page Self-tensioning No adjustment necessary No adjustment necessary Reverse Turn Bolt Indicator Here END Slot Page Trouble Shooting Waste DisposalEngine Troubleshooting Table ProblemBriggs & Stratton Electrical Diagram Hydraulic Diagram Year Limited Warranty Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Accessories

Lazer Z CT specifications

The Exmark Lazer Z CT is a standout zero-turn mower designed for both residential and commercial landscaping professionals who demand efficiency, durability, and cutting precision. This powerful mower has redefined the standards for productivity in the turf care industry, making it a popular choice among operators who handle regular and extensive mowing tasks.

One of the main features of the Lazer Z CT is its robust cutting system, which is built to deliver an exceptional quality of cut. The mower is equipped with Exmark's patented Optimized Cutting System, which includes advanced engine and deck designs that work together to deliver superior performance. With deck options ranging from 48 to 60 inches, the Lazer Z CT caters to a variety of mowing needs, allowing operators to choose the right size for their landscape.

The Lazer Z CT is powered by a range of high-performance engines, including the reliable Kohler and Kawasaki offerings. These engines are engineered for maximum torque and power, ensuring that the mower can handle tough mowing conditions with ease. The advanced cooling systems also help to prolong engine life and reduce downtime, making this mower a dependable workhorse.

In terms of technology, the Lazer Z CT features a user-friendly control system that enhances maneuverability and comfort. The intuitive control levers allow for precise handling, especially in tight spaces and around obstacles. Additionally, the padded seat and ergonomic design ensure that operators can work for extended periods without discomfort.

Another notable characteristic of the Lazer Z CT is its exceptional build quality. Constructed with heavy-duty materials, the mower is engineered to withstand the rigors of daily use. Features such as the durable steel frame and commercial-grade transmission add to its longevity, making it a sound investment for lawn care professionals.

Furthermore, the mower's maintenance-friendly design simplifies routine upkeep tasks. Features like the accessible oil filter and easy-to-reach greasing points make it convenient for operators to perform regular maintenance, ensuring the mower remains in peak condition.

In conclusion, the Exmark Lazer Z CT combines power, precision, and comfort in a zero-turn mower that meets the demands of both residential and commercial applications. With its innovative technologies and robust features, it is an excellent choice for anyone looking to enhance their mowing efficiency and quality.
Top Page Image Contents