Exmark Lazer Z CT manual Self-tensioning No adjustment necessary

Page 37

j)Recheck that blocks fit just snugly under the deck skirt and that the tension on all the chains are approximately equal. Make sure all chain attachment bolts are tight.

k)Raise deck lift lever to the 4.5” (11.4 cm) cutting height position (also transport position, See Figure 6. Adjust spring compression until proper distance is obtained between the two washers (See Figure 7) by turning the nut at the front of each spring. Lock nuts in position with jam nuts.

l)Reposition anti-scalp rollers and tighten securely.

NOTE: When above adjustments have been made, the front of the deck will be slightly lower than the rear of the deck.

4.2.3Pump Drive Belt Tension.

Self-tensioning - No adjustment necessary.

4.2.4Deck Belt Tension.

Self-tensioning - No adjustment necessary.

4.2.5Adjust Seat Switch.

a)If necessary, adjust the seat actuator rod length to where the machine will shut off when the operator raises off the seat (with brake disengaged or PTO engaged) but will continue to run with operator in seat (a slight shift in weight should not shut machine off). Normal adjustment is when length of spring is 2.09” (5.3 cm ) (with seat up).

NOTE: To prevent rough ground cut-outs the unit is equipped with a time delayed seat switch. When the operator raises off the seat with either the brake disengaged or the PTO engaged, the engine should stop after 1/2 second has elapsed.

b)To adjust seat switch, loosen lock nut on bottom of the actuator rod (5/16 x 7” bolt) and adjust the nuts to move the actuator plate up or down on the rod.

4.2.6Park Brake Adjustment.

a)Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

b)Check tire pressure. Inflate tires to 13 psi (90kpa).

c)Disengage the park brake.

d)Loosen the jam nuts next to the yoke at each end of the park brake linkage. See Figure 8.

e)Place a wrench on one of the two nuts near the front of the park brake linkage.

f)Turn the linkage until the distance from the lower front corner of the brake bar measures 1” (2.5 cm) to 1 5/16”(3.3 cm) with the park brake disengaged See Figure 8.

g)Tighten the jam nuts loosened in step d).

32

Image 37
Contents For Serial Nos 670,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Potential Hazard There is no rollover protection when the roll bar is down Page Maintenance and Storage Safety Signs Page Page Specifications Tires and Wheels Hydrostatic Ground Drive SystemCutting Deck Operation Instructions DimensionsTorque Requirements ControlsPotential Hazard Push the lever forward and down to disengage the brake Mowing PRE-STARTEngaging PTO Transporting Potential Hazard Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsService Interval Daily Check safety interlock system Service Interval 40 hr Service Interval 40 hrs Lubrication ChartService Interval Refer to chart Service Interval 160 hrs Service Interval Once YearlyService Interval As Required Service Interval 80 hrsService Interval After First 250 hrs Then yearly thereafter Service Interval After First 100 hrs Then 500 hrs thereafter Adjustments Page Self-tensioning No adjustment necessary No adjustment necessary Reverse Turn Bolt Indicator Here END Slot Page Waste Disposal Trouble ShootingProblem Engine Troubleshooting TableBriggs & Stratton Electrical Diagram Hydraulic Diagram Year Limited Warranty Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Accessories

Lazer Z CT specifications

The Exmark Lazer Z CT is a standout zero-turn mower designed for both residential and commercial landscaping professionals who demand efficiency, durability, and cutting precision. This powerful mower has redefined the standards for productivity in the turf care industry, making it a popular choice among operators who handle regular and extensive mowing tasks.

One of the main features of the Lazer Z CT is its robust cutting system, which is built to deliver an exceptional quality of cut. The mower is equipped with Exmark's patented Optimized Cutting System, which includes advanced engine and deck designs that work together to deliver superior performance. With deck options ranging from 48 to 60 inches, the Lazer Z CT caters to a variety of mowing needs, allowing operators to choose the right size for their landscape.

The Lazer Z CT is powered by a range of high-performance engines, including the reliable Kohler and Kawasaki offerings. These engines are engineered for maximum torque and power, ensuring that the mower can handle tough mowing conditions with ease. The advanced cooling systems also help to prolong engine life and reduce downtime, making this mower a dependable workhorse.

In terms of technology, the Lazer Z CT features a user-friendly control system that enhances maneuverability and comfort. The intuitive control levers allow for precise handling, especially in tight spaces and around obstacles. Additionally, the padded seat and ergonomic design ensure that operators can work for extended periods without discomfort.

Another notable characteristic of the Lazer Z CT is its exceptional build quality. Constructed with heavy-duty materials, the mower is engineered to withstand the rigors of daily use. Features such as the durable steel frame and commercial-grade transmission add to its longevity, making it a sound investment for lawn care professionals.

Furthermore, the mower's maintenance-friendly design simplifies routine upkeep tasks. Features like the accessible oil filter and easy-to-reach greasing points make it convenient for operators to perform regular maintenance, ensuring the mower remains in peak condition.

In conclusion, the Exmark Lazer Z CT combines power, precision, and comfort in a zero-turn mower that meets the demands of both residential and commercial applications. With its innovative technologies and robust features, it is an excellent choice for anyone looking to enhance their mowing efficiency and quality.