Exmark Lazer Z CT manual Reverse Turn Bolt Indicator Here END Slot

Page 39

CAUTION

POTENTIAL HAZARD

♦Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous.

WHAT CAN HAPPEN

♦The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

HOW TO AVOID THE HAZARD

♦DO NOT rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

a)This adjustment must be made with the drive wheels turning. First raise the frame and block up so that drive wheels can rotate freely.

b)Remove the electrical connection from the seat safety switch, located directly to the left of the seat switch assembly beside the hydraulic oil reservoir.

Temporarily install a jumper wire across the terminals in the connector of the wiring harness.

c)Run the unit at least 5 minutes with the drive levers at full forward speed to bring hydraulic system oil up to operating temperature.

d)Unhook seat latch and tilt seat forward.

e)Loosen lock nuts from the ball joints at each end of the RH pump control linkage (See Figure 9).

NOTE: The nuts to the rear of the unit on each rod have left-hand threads.

REVERSE

TURN BOLT INDICATOR

HERE

END OF

SLOT

LOOSEN

HERE

YOKE

 

TURN HERE

LOOSEN HERE

LOOSEN HERE

TO ADJUST

(RIGHTHAND THREAD)

(LEFTHAND THREAD)

 

 

FIGURE 9

f)Start engine. Brake must be engaged and motion control levers out to start engine. Operator does not have to be in the seat because of the jumper wire being used. Run engine at full throttle and release brake.

g)The reverse indicator spring must be correct before the following adjustments can be made. See Section 4.2.8.

34

Page 38 Page 40
Image 39
Page 38 Page 40
Contents For Serial Nos 670,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolCarbon monoxide can kill you Potential Hazard Operation Potential Hazard There is no rollover protection when the roll bar is down Page Maintenance and Storage Safety Signs Page Page Specifications Hydrostatic Ground Drive System Tires and WheelsCutting Deck Controls DimensionsOperation Instructions Torque RequirementsPotential Hazard Push the lever forward and down to disengage the brake Mowing PRE-STARTEngaging PTO Transporting Potential Hazard Maintenance & Adjustments Periodic MaintenanceService Interval Daily Service Interval Monthly Service Interval Daily or more often in dry conditionsService Interval Daily Check safety interlock system Service Interval 40 hr Lubrication Chart Service Interval 40 hrsService Interval Refer to chart Service Interval 160 hrs Service Interval Once YearlyService Interval 80 hrs Service Interval As RequiredService Interval After First 250 hrs Then yearly thereafter Service Interval After First 100 hrs Then 500 hrs thereafter Adjustments Page Self-tensioning No adjustment necessary No adjustment necessary Reverse Turn Bolt Indicator Here END Slot Page Waste Disposal Trouble ShootingProblem Engine Troubleshooting TableBriggs & Stratton Electrical Diagram Hydraulic Diagram Year Limited Warranty Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Accessories

Lazer Z CT specifications

The Exmark Lazer Z CT is a standout zero-turn mower designed for both residential and commercial landscaping professionals who demand efficiency, durability, and cutting precision. This powerful mower has redefined the standards for productivity in the turf care industry, making it a popular choice among operators who handle regular and extensive mowing tasks.

One of the main features of the Lazer Z CT is its robust cutting system, which is built to deliver an exceptional quality of cut. The mower is equipped with Exmark's patented Optimized Cutting System, which includes advanced engine and deck designs that work together to deliver superior performance. With deck options ranging from 48 to 60 inches, the Lazer Z CT caters to a variety of mowing needs, allowing operators to choose the right size for their landscape.

The Lazer Z CT is powered by a range of high-performance engines, including the reliable Kohler and Kawasaki offerings. These engines are engineered for maximum torque and power, ensuring that the mower can handle tough mowing conditions with ease. The advanced cooling systems also help to prolong engine life and reduce downtime, making this mower a dependable workhorse.

In terms of technology, the Lazer Z CT features a user-friendly control system that enhances maneuverability and comfort. The intuitive control levers allow for precise handling, especially in tight spaces and around obstacles. Additionally, the padded seat and ergonomic design ensure that operators can work for extended periods without discomfort.

Another notable characteristic of the Lazer Z CT is its exceptional build quality. Constructed with heavy-duty materials, the mower is engineered to withstand the rigors of daily use. Features such as the durable steel frame and commercial-grade transmission add to its longevity, making it a sound investment for lawn care professionals.

Furthermore, the mower's maintenance-friendly design simplifies routine upkeep tasks. Features like the accessible oil filter and easy-to-reach greasing points make it convenient for operators to perform regular maintenance, ensuring the mower remains in peak condition.

In conclusion, the Exmark Lazer Z CT combines power, precision, and comfort in a zero-turn mower that meets the demands of both residential and commercial applications. With its innovative technologies and robust features, it is an excellent choice for anyone looking to enhance their mowing efficiency and quality.
Top Page Image Contents