Exmark Lawn Mower manual Charging the Battery, Removing the Battery

Page 37

Maintenance

Charging the Battery

Removing the Battery

WARNING

Battery terminals or metal tools could short against metal machine components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.

•When removing or installing the battery, Do Not allow the battery terminals to touch any metal parts of the machine.

•Do Not allow metal tools to short between the battery terminals and metal parts of the machine.

1.Park the machine on a level surface and disengage the blade control switch.

2.Move the motion control levers outward to the neutral position, engage parking brake stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3.Raise the seat.

4.Disconnect the negative (black) ground cable from the battery post (Figure 34). Retain all fasteners.

Figure 34

1.

Battery hold-down

5.

Terminal boot

2.

Wingnut

6.

Positive battery post

3.

Negative battery post

7.

Battery

4.Bolt, washer, and nut

WARNING

Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.

•Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable.

•Always connect the positive (red) battery cable before connecting the negative (black) cable.

5.Slide the rubber cover up the positive (red) cable. Disconnect the positive (red) cable from the battery post. Retain all fasteners.

6.Remove the battery hold-down (Figure 34) and lift the battery from the battery tray.

Charging the Battery

1.Remove the battery from the chassis; refer to Removing the Battery.

2.Allowing batteries to stand for an extended period without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

3.Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table below and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart below for recommended charger settings).

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Quest California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices General OperationSlope Operation ServiceChildren TowingGeneral Service Exmark Riding Mower Safety93-7009 Safety and Instructional Decals109-6035 109-9173 109-6016 Battery Symbols Model Numbers SpecificationsSystems Dimensions Product Overview Curb WeightTorque Requirements Tread Width Center to Center of Tires, WidthwiseControls OperationOperating Instructions Think Safety FirstParking Brake Lever Height-of-Cut Foot LeverRecommended Gasoline Checking the Engine Oil Level Using Stabilizer/ConditionerStarting the Engine Gasoline/Alcohol blendsEngaging the Blades Operating the BladesUnderstanding the Safety Interlock System Safety Interlock SystemTesting the Safety Interlock System Stopping the EngineForward Driving Forward or BackwardTracking Adjustment Adjusting the Height of CutStopping the Machine BackwardPositioning the Seat Adjusting the Anti-Scalp RollersChanging the Seat Ride Suspension Adjusting the Tilt Adjusting the Motion Control LeversAdjusting the Height Pushing the Machine by HandTransporting Side DischargeTo Operate the Machine Transporting a UnitOperating Tips Keep the Underside of the Mower Clean When StoppingBlade Maintenance Cutting SpeedRecommended Maintenance Schedules MaintenanceRaising the Seat Accessing the BatteryLubrication Greasing the BearingsServicing the Air Cleaner Engine MaintenanceServicing Paper Element Servicing the Engine OilChecking the Oil Level Changing the Oil and FilterOil drain Pan Oil drain plug Change the Hydraulic System Filter Checking the Hydraulic Oil LevelInstalling the Spark Plug Cleaning the Blower HousingServicing the Spark Plug Removing the Spark PlugElectrical System Maintenance Fuel System MaintenanceReplacing the Fuel Filter Removing the Battery Charging the BatteryCharging the Battery Servicing the Fuses and Relay Installing the BatteryMower Maintenance Servicing the Cutting Blades Drive System Maintenance Checking the Tire PressureBefore Inspecting or Servicing the Blades Inspecting the BladesSharpening the Blades Removing the BladesInstalling the Blades Mower Belt MaintenanceInspecting the Belts Replacing the Mower BeltLeveling the Mower Deck Adjusting the Blade SlopeBlades front to rear Measure here Outside cutting edges Removing the Mower Deck Installing the Mower DeckLocate items shown in Figure Replacing the Discharge DeflectorWashing the Underside of the Mower CleaningStorage Cleaning and StorageProblem Possible Cause Corrective Action TroubleshootingTo Pushing the Machine by Hand Diagram-Briggs & Stratton SchematicsElectrical Diagram-Kohler For units purchased on or after January 1 Page Date Description of Work Done Service Done By Service Record

Lawn Mower specifications

Exmark Lawn Mowers are renowned for their superior quality, innovative technology, and exceptional cutting performance, making them a top choice among professional landscapers and homeowners alike. With a rich history dating back to 1982, Exmark has built a reputation for delivering mowers that are not only durable but also efficient and user-friendly.

One of the standout features of Exmark mowers is their cutting system, which includes advanced mower decks designed for precision and efficiency. The premium cutting decks are engineered to provide unparalleled grass dispersal and a clean finish. The Exmark Vantage and Lazer Z series are particularly known for their Ultracut decks, which enhance the mowing experience with an optimal blade overlap that ensures a consistent cut.

Powering these machines are robust engines that vary across the different models, allowing users to choose the right power level for their specific needs. Exmark mowers often come equipped with Kawasaki or Kohler engines that maximize torque and effortlessly handle challenging terrains.

The technology integrated into Exmark mowers includes the innovative Red Technology. It features intelligent monitoring systems that provide real-time feedback on engine performance, ensuring optimal efficiency and reducing fuel consumption. This feature is invaluable for landscape professionals who prioritize both productivity and environmental responsibility.

Comfort and ease of use are also pivotal in Exmark's design philosophy. Many models are equipped with ergonomic controls and plush seats designed to reduce operator fatigue during long mowing sessions. For instance, the Lazer Z models boast adjustable suspension seats that provide comfort without compromising control or precision.

Furthermore, Exmark mowers offer exceptional maneuverability. The zero-turn capability allows users to navigate tight spaces and obstacles with remarkable ease. This feature is particularly beneficial for commercial landscapers who need to work efficiently in complex environments.

In terms of build quality, Exmark mowers are constructed with heavy-duty materials designed to withstand rigorous use. The durability of the chassis and components ensures a long lifespan, further enhancing the investment for both professional and residential users.

Overall, Exmark Lawn Mowers combine cutting-edge technology, superior build quality, and unparalleled performance to provide a mowing experience that stands above the competition. Whether for commercial landscaping or maintaining a pristine lawn at home, Exmark continues to deliver exceptional results and user satisfaction.
Top Page Image Contents