Exmark Lawn Mower manual Blades front to rear Measure here Outside cutting edges

Page 43

Maintenance

2.Park the machine on a level surface and disengage the blade control switch.

3.Move the motion control levers outward to the neutral position, engage the parking brake, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

4.Check the air pressure of all four tires. If needed, adjust to the recommended inflation; refer to Checking the Tire Pressure in Drive System Maintenance section.

5.Check and adjust the side-to-side blade level if you have not checked the setting; refer to Leveling the Mower.

6.Set the height-of-cut lever to the 3 inch (76 mm) position. Place two 2 1/2 inch (6.35 cm) thick blocks under the rear edge of the cutting deck skirt; one on each side of the cutting deck. Place two 2 5/16 inch (5.89 cm) blocks under each side of the front edge of the deck, but not under the anti-scalp roller brackets.

7.Loosen the leveling adjust locking nuts (item 4) on all four corners so that the deck is sitting securely on all four blocks. Make sure that the deck hangers are all the way down (at the top of the slot) and the deck lift foot lever is pushed back against the stop, then tighten the four leveling adjust locking nuts (Figure 46).

Figure 46

1.

Deck lift arm

3.

Deck hanger

2.

Float retaining nut

4.

Leveling adjust locking

 

 

 

nut

8.Carefully rotate the blades so they are facing front to rear (Figure 47).

9.Measure from the tip of the front blade to the flat surface and the tip of the rear blade to the flat surface (Figure 47). If the front blade tip is not 1/16-5/16 inch (1.6-7.9 mm) lower than the rear blade tip, adjust the front deck hanger.

 

 

Figure 47

1.

Blades front to rear

3. Measure here

2.

Outside cutting edges

10.When the front-to-rear blade slope is correct check the side-to-side level of the mower again; refer to Leveling the Mower .

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Quest California Introduction Contents General Operation SafetySafety Alert Symbol Safe Operating PracticesTowing ServiceSlope Operation ChildrenGeneral Service Exmark Riding Mower Safety93-7009 Safety and Instructional Decals109-6035 109-9173 109-6016 Battery Symbols Model Numbers SpecificationsSystems Dimensions Tread Width Center to Center of Tires, Widthwise Curb WeightProduct Overview Torque RequirementsControls OperationHeight-of-Cut Foot Lever Think Safety FirstOperating Instructions Parking Brake LeverRecommended Gasoline Gasoline/Alcohol blends Using Stabilizer/ConditionerChecking the Engine Oil Level Starting the EngineEngaging the Blades Operating the BladesStopping the Engine Safety Interlock SystemUnderstanding the Safety Interlock System Testing the Safety Interlock SystemForward Driving Forward or BackwardBackward Adjusting the Height of CutTracking Adjustment Stopping the MachinePositioning the Seat Adjusting the Anti-Scalp RollersChanging the Seat Ride Suspension Pushing the Machine by Hand Adjusting the Motion Control LeversAdjusting the Tilt Adjusting the HeightTransporting a Unit Side DischargeTransporting To Operate the MachineOperating Tips Cutting Speed When StoppingKeep the Underside of the Mower Clean Blade MaintenanceRecommended Maintenance Schedules MaintenanceGreasing the Bearings Accessing the BatteryRaising the Seat LubricationServicing the Air Cleaner Engine MaintenanceChanging the Oil and Filter Servicing the Engine OilServicing Paper Element Checking the Oil LevelOil drain Pan Oil drain plug Change the Hydraulic System Filter Checking the Hydraulic Oil LevelRemoving the Spark Plug Cleaning the Blower HousingInstalling the Spark Plug Servicing the Spark PlugElectrical System Maintenance Fuel System MaintenanceReplacing the Fuel Filter Removing the Battery Charging the BatteryCharging the Battery Servicing the Fuses and Relay Installing the BatteryInspecting the Blades Drive System Maintenance Checking the Tire PressureMower Maintenance Servicing the Cutting Blades Before Inspecting or Servicing the BladesSharpening the Blades Removing the BladesReplacing the Mower Belt Mower Belt MaintenanceInstalling the Blades Inspecting the BeltsLeveling the Mower Deck Adjusting the Blade SlopeBlades front to rear Measure here Outside cutting edges Removing the Mower Deck Installing the Mower DeckLocate items shown in Figure Replacing the Discharge DeflectorWashing the Underside of the Mower CleaningStorage Cleaning and StorageProblem Possible Cause Corrective Action TroubleshootingTo Pushing the Machine by Hand Diagram-Briggs & Stratton SchematicsElectrical Diagram-Kohler For units purchased on or after January 1 Page Date Description of Work Done Service Done By Service Record

Lawn Mower specifications

Exmark Lawn Mowers are renowned for their superior quality, innovative technology, and exceptional cutting performance, making them a top choice among professional landscapers and homeowners alike. With a rich history dating back to 1982, Exmark has built a reputation for delivering mowers that are not only durable but also efficient and user-friendly.

One of the standout features of Exmark mowers is their cutting system, which includes advanced mower decks designed for precision and efficiency. The premium cutting decks are engineered to provide unparalleled grass dispersal and a clean finish. The Exmark Vantage and Lazer Z series are particularly known for their Ultracut decks, which enhance the mowing experience with an optimal blade overlap that ensures a consistent cut.

Powering these machines are robust engines that vary across the different models, allowing users to choose the right power level for their specific needs. Exmark mowers often come equipped with Kawasaki or Kohler engines that maximize torque and effortlessly handle challenging terrains.

The technology integrated into Exmark mowers includes the innovative Red Technology. It features intelligent monitoring systems that provide real-time feedback on engine performance, ensuring optimal efficiency and reducing fuel consumption. This feature is invaluable for landscape professionals who prioritize both productivity and environmental responsibility.

Comfort and ease of use are also pivotal in Exmark's design philosophy. Many models are equipped with ergonomic controls and plush seats designed to reduce operator fatigue during long mowing sessions. For instance, the Lazer Z models boast adjustable suspension seats that provide comfort without compromising control or precision.

Furthermore, Exmark mowers offer exceptional maneuverability. The zero-turn capability allows users to navigate tight spaces and obstacles with remarkable ease. This feature is particularly beneficial for commercial landscapers who need to work efficiently in complex environments.

In terms of build quality, Exmark mowers are constructed with heavy-duty materials designed to withstand rigorous use. The durability of the chassis and components ensures a long lifespan, further enhancing the investment for both professional and residential users.

Overall, Exmark Lawn Mowers combine cutting-edge technology, superior build quality, and unparalleled performance to provide a mowing experience that stands above the competition. Whether for commercial landscaping or maintaining a pristine lawn at home, Exmark continues to deliver exceptional results and user satisfaction.
Top Page Image Contents