Exmark Lawn Mower manual Servicing the Fuses and Relay, Installing the Battery

Page 38

Maintenance

Voltage

Percent

Maximum

Charging

Reading

Charge

Charger

Interval

 

 

Settings

 

12.6 or

100%

16 volts/7

No

greater

 

amps

Charging

 

 

 

Required

12.4 – 12.6

75–100%

16 volts/7

30 Minutes

 

 

amps

 

12.2 – 12.4

50–75%

16 volts/7

1 Hour

 

 

amps

 

12.0–12.2

25–50%

14.4 volts/4

2 Hours

 

 

amps

 

11.7–12.0

0–25%

14.4 volts/4

3 Hours

 

 

amps

 

11.7 or less

0%

14.4 volts/2

6 Hours or

 

 

amps

More

4.When the battery is fully charged, unplug the charger from the electrical outlet, then disconnect the charger leads from the battery posts (Figure 35).

Figure 35

1.

Negative battery post

3.

Red (+) charger lead

2.

Black (-) charger lead

4.

Positive battery post

Note: Do Not run the machine with the battery disconnected, electrical damage may occur.

Installing the Battery

1.Position the battery in the tray with the terminal posts toward the operating position (Figure 34).

2.Install the positive (red) battery cable to the positive (+) battery terminal using the fasteners removed previously

3.Install the negative battery cable to the negative (-) battery terminal using the fasteners removed previously.

4.Slide the red terminal boot onto the positive (red) battery post.

5.Secure the battery with the hold-down (Figure 34).

Servicing the Fuses and Relay

The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short. There is also a replaceable relay/s next to the fuse. Refer to your Parts manual for correct replacement components.

Fuse Block:

Main fuse: 25 amp fuse, blade-type

Charge Circuit: 20 amp fuse, blade-type

Auxiliary circuit: 15 amp fuse, blade-type

Diode: TVS

1.Raise the seat to gain access to the fuse holder (Figure 36).

Figure 36

1.

Cover

5.

Main–25 amp

2.

Relay

6.

Diode

3.

Auxilliary–15 amp

7.

Briggs & Stratton unit

4.

Charge–20 amp

8.

Kohler Command unit

 

 

 

 

38

Image 38
Contents Quest California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol General OperationChildren ServiceSlope Operation TowingExmark Riding Mower Safety General ServiceSafety and Instructional Decals 93-7009109-6035 109-9173 109-6016 Battery Symbols Systems SpecificationsModel Numbers Dimensions Torque Requirements Curb WeightProduct Overview Tread Width Center to Center of Tires, WidthwiseOperation ControlsParking Brake Lever Think Safety FirstOperating Instructions Height-of-Cut Foot LeverRecommended Gasoline Starting the Engine Using Stabilizer/ConditionerChecking the Engine Oil Level Gasoline/Alcohol blendsOperating the Blades Engaging the BladesTesting the Safety Interlock System Safety Interlock SystemUnderstanding the Safety Interlock System Stopping the EngineDriving Forward or Backward ForwardStopping the Machine Adjusting the Height of CutTracking Adjustment BackwardChanging the Seat Ride Suspension Adjusting the Anti-Scalp RollersPositioning the Seat Adjusting the Height Adjusting the Motion Control LeversAdjusting the Tilt Pushing the Machine by HandTo Operate the Machine Side DischargeTransporting Transporting a UnitOperating Tips Blade Maintenance When StoppingKeep the Underside of the Mower Clean Cutting SpeedMaintenance Recommended Maintenance SchedulesLubrication Accessing the BatteryRaising the Seat Greasing the BearingsEngine Maintenance Servicing the Air CleanerChecking the Oil Level Servicing the Engine OilServicing Paper Element Changing the Oil and FilterOil drain Pan Oil drain plug Checking the Hydraulic Oil Level Change the Hydraulic System FilterServicing the Spark Plug Cleaning the Blower HousingInstalling the Spark Plug Removing the Spark PlugReplacing the Fuel Filter Fuel System MaintenanceElectrical System Maintenance Charging the Battery Charging the BatteryRemoving the Battery Installing the Battery Servicing the Fuses and RelayBefore Inspecting or Servicing the Blades Drive System Maintenance Checking the Tire PressureMower Maintenance Servicing the Cutting Blades Inspecting the BladesRemoving the Blades Sharpening the BladesInspecting the Belts Mower Belt MaintenanceInstalling the Blades Replacing the Mower BeltAdjusting the Blade Slope Leveling the Mower DeckBlades front to rear Measure here Outside cutting edges Installing the Mower Deck Removing the Mower DeckReplacing the Discharge Deflector Locate items shown in FigureCleaning Washing the Underside of the MowerCleaning and Storage StorageTroubleshooting Problem Possible Cause Corrective ActionTo Pushing the Machine by Hand Schematics Diagram-Briggs & StrattonElectrical Diagram-Kohler For units purchased on or after January 1 Page Service Record Date Description of Work Done Service Done By

Lawn Mower specifications

Exmark Lawn Mowers are renowned for their superior quality, innovative technology, and exceptional cutting performance, making them a top choice among professional landscapers and homeowners alike. With a rich history dating back to 1982, Exmark has built a reputation for delivering mowers that are not only durable but also efficient and user-friendly.

One of the standout features of Exmark mowers is their cutting system, which includes advanced mower decks designed for precision and efficiency. The premium cutting decks are engineered to provide unparalleled grass dispersal and a clean finish. The Exmark Vantage and Lazer Z series are particularly known for their Ultracut decks, which enhance the mowing experience with an optimal blade overlap that ensures a consistent cut.

Powering these machines are robust engines that vary across the different models, allowing users to choose the right power level for their specific needs. Exmark mowers often come equipped with Kawasaki or Kohler engines that maximize torque and effortlessly handle challenging terrains.

The technology integrated into Exmark mowers includes the innovative Red Technology. It features intelligent monitoring systems that provide real-time feedback on engine performance, ensuring optimal efficiency and reducing fuel consumption. This feature is invaluable for landscape professionals who prioritize both productivity and environmental responsibility.

Comfort and ease of use are also pivotal in Exmark's design philosophy. Many models are equipped with ergonomic controls and plush seats designed to reduce operator fatigue during long mowing sessions. For instance, the Lazer Z models boast adjustable suspension seats that provide comfort without compromising control or precision.

Furthermore, Exmark mowers offer exceptional maneuverability. The zero-turn capability allows users to navigate tight spaces and obstacles with remarkable ease. This feature is particularly beneficial for commercial landscapers who need to work efficiently in complex environments.

In terms of build quality, Exmark mowers are constructed with heavy-duty materials designed to withstand rigorous use. The durability of the chassis and components ensures a long lifespan, further enhancing the investment for both professional and residential users.

Overall, Exmark Lawn Mowers combine cutting-edge technology, superior build quality, and unparalleled performance to provide a mowing experience that stands above the competition. Whether for commercial landscaping or maintaining a pristine lawn at home, Exmark continues to deliver exceptional results and user satisfaction.