Exmark TR23KC Install Seat, Install Rear Steering Wheel, Install Drive Wheels, Install Handle BAR

Page 18

(black) cable to the negative terminal on the battery. Reinstall insulator boots. Reinstall battery cover.

NOTE: If time does not permit charging the battery, or if charging equipment is not available, connect the negative battery cables and run the vehicle continuously for 20 to 30 minutes to sufficiently charge the battery.

PART NO. 1-513747

LOCATION: Battery Cover

3.3INSTALL SEAT:

Remove seat cushion from seat frame. Remove seat frame from crate and discard mounting hardware. Mount seat to unit using two 5/16-18 x 3/4” bolts, two 3/8 flat washers and whizlock nuts from bolt bag in front two holes. Install flat washers between seat frame and seat rails. Mount seat to two rear bolts (which have springs on them), by removing the top whizlock nuts, installing seat frame, and replacing nuts. Reinstall cushion to seat frame.

3.4INSTALL REAR STEERING WHEEL:

Mount the rear tire and wheel assembly with a 5/8-11 x 10-1/2” bolt and torque nut. Tighten torque nut just enough to create a slight drag on the wheel while the wheel is being rotated. Inflate tire to 14 psi (95 kPa).

3.5INSTALL DRIVE WHEELS:

Mount both drive wheels securing them with four (4) wheel nuts each. Torque to 90-95 ft. lbs. (122-129 N-m). Inflate tires to 20 psi (138 kPa).

3.6INSTALL HANDLE BAR:

Install steering handle bar with two 3/8-16 x 1-1/4” bolts and two 3/8 spring disc washers.

3.7INSTALL CANISTER AIR CLEANER:

a)Remove air cleaner (with bracket attached) from crate. Keep air cleaner and mounting bracket together.

b)Cut plastic tie holding air cleaner cap to engine and install cap to the air cleaner.

c)Remove the top two throttle plate mounting screws from the engine. Keep screws for re-attaching air cleaner.

d)Position the air cleaner assembly over the engine, aligning air cleaner bracket holes with top holes in the throttle plate. Reinstall throttle plate screws through air cleaner bracket and throttle plate.

e)Mount lower holes in air cleaner bracket to holes in engine air cleaner bracket using (2) M6x1.0x16mm Hex flange capscrews, (2) .216 I.D. x 1.0 O.D. washers, and (2) M6x1.0 nyloc nuts from bolt bag. Be sure to install the head of the capscrew to the front of the unit and the washer next to the nyloc nut to the rear of the unit on the other side of the air cleaner bracket.

f)Remove plastic plugs from air intake elbow on engine and air cleaner hose. Adjust the air cleaner and hose as required and connect intake hose to air cleaner outlet. Position and tighten the two hose clamps to secure the hose connections.

3.8INSTALL MOWER DECK TO TRACTOR:

3.8.1Rotate drive wheel release lever into position shown in Figure 4 to release drive system (Refer to Section 4.11). Roll tractor to mower deck and mower deck support aligning them so the tractor is positioned for ease of mounting the deck support. Remove center belt shield.

-13 -

Image 18
Contents For Turf Ranger Serial Nos ,000 & Higher FMD524 & FMD604 Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Your Safety is Involved SafetySafety Alert Symbol TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing Page Maintenance and Storage Safety Signs Page Specifications Mower Deck DimensionsTires Torque RequirementsAssembly Instructions Service BatteryInstall Drive Wheels Install SeatInstall Rear Steering Wheel Install Handle BARHardware and Support PIN Location for Deck Support Frame Controls Idler Pulley KIT and LocationPosition Discharge Chute Page Mowing Operation InstructionsPRE-START Drive Wheel Release LeverTransporting Maintenance & Adjustments Periodic MaintenanceService Interval Daily Blade Bolt Installation For Serial Nos ,000 539,999Blade Bolt Installation Page Page Lubrication Chart Fitting Locations Initial Service Pumps PlacesCaster Wheel Assembly Page Page Adjustments Cutting Height AdjustmentANTI-SCALP Roller Installation Cutting Height Adjustment Potential Hazard Neutral Centering Device Adjustment Parking Brake Quadrant AdjustmentBrake Control Link and Spring Adjustment Parking Brake Neutral Lockout Adjustment Motion Control Linkage Adjustment Seat Switch AdjustmentElectric Clutch Adjustment Armrest Adjustment Throttle TensionTrouble Shooting Waste DisposalEngine Troubleshooting Engine Troubleshooting TableProblem Wiring Diagrams Year Limited Warranty Exmark Turf Equipment Page Page Service Record Page See EXMARK’S Complete Line of Accessories

TR23KC specifications

The Exmark TR23KC is a stand-on mower that has gained attention in the landscaping industry for its superior performance and innovative features. Designed for both commercial and residential landscaping professionals, this model combines power, precision, and comfort in a versatile package that is ideal for a range of mowing applications.

One of the standout features of the TR23KC is its robust engine. Powered by a reliable Kawasaki engine, the mower delivers exceptional cutting performance, making it suitable for tackling tough grass and uneven terrain. The engine ensures optimal fuel efficiency while providing enough power to handle demanding mowing tasks. This reliability allows landscapers to complete jobs quickly without sacrificing quality.

The cutting deck is another remarkable feature of the TR23KC. With a cutting width of 48 inches, it allows for efficient mowing over large areas. The deck is fabricated from high-quality materials, offering durability and resistance to wear and tear. The mower has adjustable cutting heights, enabling users to achieve the desired grass length, which is particularly beneficial for maintaining varying lawn conditions throughout the seasons.

In terms of comfort, the Exmark TR23KC includes an ergonomic stand-on platform. This design not only provides ease of use but also enhances operator visibility, offering an unobstructed view of the cutting area. The platform is equipped with anti-vibration features, reducing fatigue during long working hours, while the intuitive controls facilitate ease of use.

One notable technology integrated into the TR23KC is Exmark's innovative wheel technology. The large drive wheels enhance maneuverability and traction, allowing the operator to navigate around obstacles with utmost precision. The zero-turn capability further enhances its agility, making it simple to turn around tight corners and narrow spaces without needing to reposition.

Safety is also prioritized in the design of the TR23KC. It features an automatic engine shut-off system that activates when the operator leaves the platform. This ensures that the mower remains safe to use and reduces the risk of accidents.

Overall, the Exmark TR23KC stand-on mower is an excellent choice for professionals seeking a machine that combines power, efficiency, and comfort. Its robust engine, durable cutting deck, ergonomic design, and advanced technologies make it a reliable option for tackling various mowing tasks, establishing it as a leader in the stand-on mower segment.