Exmark TR23KC manual

Page 29

6.1.11Check tire pressures: Service Interval: 40 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Inflate tires to pressures specified in Section 2.8 (Specifications).

c)See Section 8.1 for further information.

NOTE: Do not add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires may cause failures to the hydro drive system, frame, and other components. Foam filling tires will void the warranty.

6.1.12Check battery charge: Service Interval: Monthly

Allowing batteries to stand for an extended period of time without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

a)Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table below and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

IMPORTANT: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart below for recommended charger settings).

Voltage

Percent

Maximum

 

Charging Interval

Reading

Charge

Charger Settings

 

 

 

12.6 or greater

100%

16 volts/7 amps

No Charging Required

12.4 – 12.6

75

– 100%

16 volts/7 amps

30 Minutes

12.2 – 12.4

50

– 75%

16 volts/7 amps

1

Hour

12.0 – 12.2

25

– 50%

14.4 volts/4 amps

2

Hours

11.7 – 12.0

0 – 25%

14.4 volts/4 amps

3

Hours

11.7 or less

0%

14.4 volts/2 amps

6

Hours or More

6.1.13 Inspect Belt Wear:

Service Interval: 40 hrs.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Remove the three mower deck belt shields to check mower primary and secondary belt condition.

c)Look under engine deck to check the transmission drive belt condition.

d)Check all idler arms to be sure they pivot freely.

Note: Be sure to check idler on transmission drive belt. Disassemble, clean and grease pivot bushing if necessary.

6.1.14Lubricate grease fittings.

a)Stop engine, wait for all moving parts to stop, and remove key.

b)Lubricate fittings with one to two pumps NGLI grade #2 multi-purpose gun grease. Refer to the following chart for fitting locations and lubrication schedule.

-24 -

Image 29
Contents For Turf Ranger Serial Nos ,000 & Higher FMD524 & FMD604 Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing Page Maintenance and Storage Safety Signs Page Specifications Tires DimensionsMower Deck Torque RequirementsService Battery Assembly InstructionsInstall Rear Steering Wheel Install SeatInstall Drive Wheels Install Handle BARHardware and Support PIN Location for Deck Support Frame Position Discharge Chute ControlsIdler Pulley KIT and Location Page PRE-START Operation InstructionsMowing Drive Wheel Release LeverTransporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily For Serial Nos ,000 539,999 Blade Bolt InstallationBlade Bolt Installation Page Page Caster Wheel Assembly Lubrication ChartFitting Locations Initial Service Pumps Places Page Page Cutting Height Adjustment AdjustmentsANTI-SCALP Roller Installation Cutting Height Adjustment Potential Hazard Brake Control Link and Spring Adjustment Neutral Centering Device AdjustmentParking Brake Quadrant Adjustment Parking Brake Neutral Lockout Adjustment Electric Clutch Adjustment Motion Control Linkage AdjustmentSeat Switch Adjustment Throttle Tension Armrest AdjustmentWaste Disposal Trouble ShootingProblem Engine TroubleshootingEngine Troubleshooting Table Wiring Diagrams Year Limited Warranty Exmark Turf Equipment Page Page Service Record Page See EXMARK’S Complete Line of Accessories

TR23KC specifications

The Exmark TR23KC is a stand-on mower that has gained attention in the landscaping industry for its superior performance and innovative features. Designed for both commercial and residential landscaping professionals, this model combines power, precision, and comfort in a versatile package that is ideal for a range of mowing applications.

One of the standout features of the TR23KC is its robust engine. Powered by a reliable Kawasaki engine, the mower delivers exceptional cutting performance, making it suitable for tackling tough grass and uneven terrain. The engine ensures optimal fuel efficiency while providing enough power to handle demanding mowing tasks. This reliability allows landscapers to complete jobs quickly without sacrificing quality.

The cutting deck is another remarkable feature of the TR23KC. With a cutting width of 48 inches, it allows for efficient mowing over large areas. The deck is fabricated from high-quality materials, offering durability and resistance to wear and tear. The mower has adjustable cutting heights, enabling users to achieve the desired grass length, which is particularly beneficial for maintaining varying lawn conditions throughout the seasons.

In terms of comfort, the Exmark TR23KC includes an ergonomic stand-on platform. This design not only provides ease of use but also enhances operator visibility, offering an unobstructed view of the cutting area. The platform is equipped with anti-vibration features, reducing fatigue during long working hours, while the intuitive controls facilitate ease of use.

One notable technology integrated into the TR23KC is Exmark's innovative wheel technology. The large drive wheels enhance maneuverability and traction, allowing the operator to navigate around obstacles with utmost precision. The zero-turn capability further enhances its agility, making it simple to turn around tight corners and narrow spaces without needing to reposition.

Safety is also prioritized in the design of the TR23KC. It features an automatic engine shut-off system that activates when the operator leaves the platform. This ensures that the mower remains safe to use and reduces the risk of accidents.

Overall, the Exmark TR23KC stand-on mower is an excellent choice for professionals seeking a machine that combines power, efficiency, and comfort. Its robust engine, durable cutting deck, ergonomic design, and advanced technologies make it a reliable option for tackling various mowing tasks, establishing it as a leader in the stand-on mower segment.