Exmark TR23KC manual

Page 21

4.3Electro-mechanical deck lift control: Switch is located on left side of control console. Moving the toggle switch lever forward will lower the cutting deck. Moving the lever backward will raise the deck. Normal operation is with the actuator fully extended. The actuator has an internal clutch to protect it from excessive loads. When raising or lowering the deck and the actuator has reached it’s limit, a "ratcheting" sound is heard. When this ratcheting sound is heard, release switch lever, momentarily reverse switch to move actuator just off the fully extended or retracted position.

4.4PTO Engagement: Located on right side of control console. The switch must be pulled out to the “ROTATE” position to engage the blades. The switch is pushed in to the “STOP” position to stop the blades. Operator must be in the seat when blades are engaged or engine will stop.

4.5Choke Control: Located on the left side of the control console. The choke control is used to aid in starting a cold engine. The choke control is pulled out to be in the “ON” position and pushed in to be in the “OFF” position. DO NOT run a warm engine with the choke in the “ON” position.

4.6Throttle Control: Located on the control console right side. Throttle is used to control engine speed. Moving throttle control ahead will increase engine speed and moving it to the rear will decrease engine speed.

4.7Park Brake Lever: Located ahead and near the right side of control console. Park brake lever engages a parking brake on the drive wheels and also locks the hydrostatic drive system in neutral. Moving the lever rearward will engage the brake. To disengage brake, lift finger latch and move brake ahead. Operator must be in the seat when brake is disengaged or engine will stop.

4.8Ignition Switch: Located on the control console just ahead of the steering handle. The ignition switch is used to start and stop the engine. The switch has three positions “OFF”, “ON” and “START”. Insert key into switch and rotate to the right to the "ON" position. Rotate clockwise to the next position to engage the starter (key must be held against spring pressure in this position). Operator must be in seat with brake engaged and PTO disengaged to start engine. When engine starts, release key. DO NOT leave key in the “ON” position without engine running, this will run down the battery.

4.9Hour Meter: Located on the steering console just below the steering wheel. The hour meter is connected to a pressure switch installed in the engine block and it records the number of hours that the engine has run. If ignition switch is left on without engine running, hour meter will not run.

NOTE: This switch is not a low oil sensor and will not alert the operator if the engine oil is low.

4.10Fuel Shut-Off Valve: Located in the fuel line near the right rear corner of the engine. The fuel shut-off valve is used to shut off the flow of fuel when parking inside a building, during transportation to and from job sites and when the machine will not be used for a few days. Rotate valve 1/4 turn clockwise to shut fuel off. Rotate valve 1/4 turn counter-clockwise to turn fuel on.

4.11Drive Wheel Release Lever: Located under the lower left rear corner of the engine deck (See Figure 4). The drive wheel release lever is used to release the hydrostatic drive system to allow machine to be pushed while the engine is not running. Rotate lever 1/8 turn counter-clockwise until caught under spring latch to release drive system. Pull spring latch out far enough to allow lever to rotate 1/8 turn clockwise to engage drive system.

NOTE: Do Not tow machine or transmission damage may result.

-16 -

Page 20 Page 22
Image 21
Page 20 Page 22
Contents For Turf Ranger Serial Nos ,000 & Higher FMD524 & FMD604 Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing Page Maintenance and Storage Safety Signs Page Specifications Tires DimensionsMower Deck Torque RequirementsService Battery Assembly InstructionsInstall Rear Steering Wheel Install SeatInstall Drive Wheels Install Handle BARHardware and Support PIN Location for Deck Support Frame Controls Idler Pulley KIT and LocationPosition Discharge Chute Page PRE-START Operation InstructionsMowing Drive Wheel Release LeverTransporting Periodic Maintenance Maintenance & AdjustmentsService Interval Daily For Serial Nos ,000 539,999 Blade Bolt InstallationBlade Bolt Installation Page Page Lubrication Chart Fitting Locations Initial Service Pumps PlacesCaster Wheel Assembly Page Page Cutting Height Adjustment AdjustmentsANTI-SCALP Roller Installation Cutting Height Adjustment Potential Hazard Neutral Centering Device Adjustment Parking Brake Quadrant AdjustmentBrake Control Link and Spring Adjustment Parking Brake Neutral Lockout Adjustment Motion Control Linkage Adjustment Seat Switch AdjustmentElectric Clutch Adjustment Throttle Tension Armrest AdjustmentWaste Disposal Trouble ShootingEngine Troubleshooting Engine Troubleshooting TableProblem Wiring Diagrams Year Limited Warranty Exmark Turf Equipment Page Page Service Record Page See EXMARK’S Complete Line of Accessories

TR23KC specifications

The Exmark TR23KC is a stand-on mower that has gained attention in the landscaping industry for its superior performance and innovative features. Designed for both commercial and residential landscaping professionals, this model combines power, precision, and comfort in a versatile package that is ideal for a range of mowing applications.

One of the standout features of the TR23KC is its robust engine. Powered by a reliable Kawasaki engine, the mower delivers exceptional cutting performance, making it suitable for tackling tough grass and uneven terrain. The engine ensures optimal fuel efficiency while providing enough power to handle demanding mowing tasks. This reliability allows landscapers to complete jobs quickly without sacrificing quality.

The cutting deck is another remarkable feature of the TR23KC. With a cutting width of 48 inches, it allows for efficient mowing over large areas. The deck is fabricated from high-quality materials, offering durability and resistance to wear and tear. The mower has adjustable cutting heights, enabling users to achieve the desired grass length, which is particularly beneficial for maintaining varying lawn conditions throughout the seasons.

In terms of comfort, the Exmark TR23KC includes an ergonomic stand-on platform. This design not only provides ease of use but also enhances operator visibility, offering an unobstructed view of the cutting area. The platform is equipped with anti-vibration features, reducing fatigue during long working hours, while the intuitive controls facilitate ease of use.

One notable technology integrated into the TR23KC is Exmark's innovative wheel technology. The large drive wheels enhance maneuverability and traction, allowing the operator to navigate around obstacles with utmost precision. The zero-turn capability further enhances its agility, making it simple to turn around tight corners and narrow spaces without needing to reposition.

Safety is also prioritized in the design of the TR23KC. It features an automatic engine shut-off system that activates when the operator leaves the platform. This ensures that the mower remains safe to use and reduces the risk of accidents.

Overall, the Exmark TR23KC stand-on mower is an excellent choice for professionals seeking a machine that combines power, efficiency, and comfort. Its robust engine, durable cutting deck, ergonomic design, and advanced technologies make it a reliable option for tackling various mowing tasks, establishing it as a leader in the stand-on mower segment.
Top Page Image Contents