Exmark 000 & higher, 312 manual Specifications, Model Numbers, Systems

Page 15

Specifications

Specifications

Model Numbers

Serial Nos: 312,000,000 and Higher

PNS600KA443; PNS651KA483; PNS680KC523; PNS740KC604

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

Engine Oil Type: Exmark 4–Cycle Premium Engine Oil

RPM: Full Speed:

Kawasaki: 3750 ±50 RPM (PTO not engaged)

Idle: 1500 ±100 RPM

Kohler: 3700 ±50 RPM (PTO not engaged) Idle: 1500 ±100 RPM

Fuel System

Capacity: 7.0 gal. (26.5 L)

Fuel Recommendations:

Electrical System

Charging System: Flywheel Alternator

Charging Capacity: 15 amps

Battery Type: BCI Group U1

Recommended Minimum Battery CCA: 260 CCA

Battery Voltage: 12 Volt

Polarity: Negative Ground

Fuses: All units:

25 amp main fuse

20 amp charging system fuse

10 amp PTO fuse

15 amp accessory fuse

Safety Interlock System

For best results, use only clean, fresh, unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method).

Oxygenated fuel with up to 10% ethanol or 15% MTBE by volume is acceptable.

Do Not use ethanol blends of gasoline (such as E15 or E85) with more than 10% ethanol by volume. Performance problems and/or engine damage may result which may not be covered under warranty.

Do Not use gasoline containing methanol.

Do Not store fuel either in the fuel tank or fuel containers over the winter unless a fuel stabilizer is used.

Do Not add oil to gasoline.

Fuel Filter:

Kohler: Kohler P/N 24 050 13

Kawasaki: Kawasaki P/N 49019-7005

Fuel Shut-Off Valve:

All Units: 1/4 turn increments (“ON”, “OFF”).

LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

Steering and Motion Control:

Note: Motion control levers are adjustable to three heights.

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

15

Image 15
Contents Pioneer S-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 107-2102 109-3148 109-6014 116-1119 116-1496 116-3303 116-6363 116-4430 Specifications Model NumbersSystems Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsOverall Height DimensionsOverall Width Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightProduct Overview Torque RequirementsControls OperationHour Meter Drive Wheel Release ValvesFuel Shut-Off Valve Transport Lock PTO Engagement SwitchPre-Start Deck Lift PedalOperating Instructions Raise the Rollover Protection System RopsOpen the Fuel Shut-Off Valve Stopping the Engine Starting the EngineEngaging the PTO Disengaging the PTODriving Forward Adjusting the Anti-Scalp Rollers Adjusting the Cutting HeightTransporting Transporting a UnitLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Battery Charge Recommended Jump Starting ProcedureCheck Engine Oil Level Check Mower Blades Do Not jump start a weak battery if these conditions existService Dealer Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltLubricate Caster Wheel Hubs Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Check Spark Arrester if equipped Deck Leveling Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseInch Deck Adjusting the Blade SlopeAdjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Full Forward Tracking Adjustment Motion Control Handle AdjustmentMotion Control Linkage Adjustment Removing the Shim Adjusting the Seat Ride SuspensionBrake mounting bolt Shim Clean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling FinsBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Electrical Diagram SchematicsElectrical Logic Schematic Pioneer S-Series Turf Equipment Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.