Exmark 312, 000 & higher manual Adjusting the Seat Ride Suspension, Removing the Shim

Page 40

Maintenance

11. Raise the deck and re-install the height of cut pin. Electric Clutch Adjustment

12. Check that the machine does not creep in neutral with the park brake disengaged.

Adjusting the Seat Ride Suspension

The number of seat springs can be changed to maximize rider comfort. More springs should be used with heavier operators and on rough terrain. Fewer springs should be used with lighter operators and when mowing smooth, well established lawns. Always keep the number of springs on the left and right side the same when adding and removing springs.

Figure 33

1.

Bolt

3.

Nut

2.

Spring

4.

Additional mounting

 

 

 

holes

 

 

 

 

Up to five springs can be secured to the seat box with a nut and bolt, see Figure 33.

Refer to the Parts Manual for spring and hardware part numbers.

Figure 34

1.

Armature

5.

Brake spacer

2.

Field shell

6.

Re-gap shim

3.

Rotor

7.

Brake pole

4.Brake mounting bolt

Removing the Shim:

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake. Allow the machine to cool completely before starting these instructions.

2.Using a pneumatic line, blow out any debris from under the brake pole and around the brake spacers.

3.Check the condition of the wire harness leads, connectors, and terminals. Clean or repair as necessary.

4.Verify that 12V is present at the clutch connector when the PTO switch is engaged.

5.Measure the gap between the rotor and armature. If the gap is greater than .04 inch (1 mm), proceed with the following steps:

A.Loosen both brake mounting bolts one-half to one full turn (see Figure 35).

Note: Do Not remove the brake pole from the field shell/armature. The brake pole has worn to match the armature and needs to continue to match after the shim is removed to ensure proper brake torque.

40

Image 40
Contents Pioneer S-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 107-2102 109-3148 109-6014 116-1119 116-1496 116-3303 116-6363 116-4430 Model Numbers SpecificationsSystems Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Overall WidthOverall Length Overall HeightCurb Weight Product OverviewTorque Requirements Wheel Base Center of Caster Tire to Center of Drive TireOperation ControlsDrive Wheel Release Valves Hour MeterFuel Shut-Off Valve PTO Engagement Switch Pre-StartDeck Lift Pedal Transport LockRaise the Rollover Protection System Rops Operating InstructionsOpen the Fuel Shut-Off Valve Starting the Engine Engaging the PTODisengaging the PTO Stopping the EngineDriving Forward Adjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting a Unit TransportingLoading a Unit Maintenance Recommended Maintenance SchedulesRecommended Jump Starting Procedure Check Battery ChargeCheck Engine Oil Level Do Not jump start a weak battery if these conditions exist Check Mower BladesCheck Safety Interlock System Service DealerService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareCheck Hydraulic Oil Level Lubricate Grease FittingsCheck Tire Pressures Lubricate Caster Wheel HubsChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter and Fluid Check Spark Arrester if equipped Thread Locking Adhesives Copper-Based Anti-seizeDielectric Grease Deck LevelingAdjusting the Blade Slope Inch DeckPump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Motion Control Handle Adjustment Full Forward Tracking AdjustmentMotion Control Linkage Adjustment Adjusting the Seat Ride Suspension Removing the ShimBrake mounting bolt Shim Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Schematics Electrical DiagramElectrical Logic Schematic Pioneer S-Series Turf Equipment Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.