Exmark 000 & higher, 312 manual Pre-Start, PTO Engagement Switch, Deck Lift Pedal, Transport Lock

Page 21

Operation

Figure 9

1.Front of the machine

2.Rotate bypass release knob counterclockwise to loosen

3.Lever position for operating the machine

4.Pull lever in this direction to push the machine

5.Lever position for pushing the machine

6.Rotate bypass release knob clockwise to tighten

7.Release lever

To release the drive system (see item 1 in Figure 9), loosen the knob by turning counterclockwise. Then pull the release lever on the underside of machine towards the back of the machine and retighten the knob to hold the release lever back in the released state. Repeat this on each side of the machine.

Release the parking brake. The machine is now able to be pushed by hand.

To reset the drive system (see item 2 in Figure 9), loosen the knob by turning counterclockwise. Then push the release lever on the underside of machine towards the front of the machine and retighten the knob to hold the release lever in the operating state. Repeat this on each side of the machine.

Do Not tow machine.

PTO Engagement Switch

Located on right console (see Figure 6).

Switch must be pulled out (up) to engage the blades. Switch is pushed in to disengage the blades.

Deck Lift Pedal

Located at the right front corner of the floor pan.

Push the pedal forward with your foot to raise the cutting deck. Allow the pedal to move rearward to lower the cutting deck to the cut height that has been set.

Figure 10

1.

Transport lock handle

3.

Height of cut decal

2.

Height adjustment pin

4.

Deck foot pedal

 

 

 

 

Transport Lock

Located on the height of cut adjustment plate (see Figure 10).

The transport latching mechanism will automatically engage when the deck is raised to the transport position. To release the deck from the transport position: push the foot pedal to remove the load from the transport latching mechanism, pull the transport lock handle rearward, and let the pedal come back to lower the deck down to the desired cut height.

Pre-Start

Fill fuel tanks. See Fuel Recommendations in the Specifications section for additional gasoline information.

Do Not add oil to gasoline.

Do Not overfill fuel tank. Fill the fuel tank to the bottom of the filler neck. The empty space in the tank allows gasoline to expand. Overfilling may result in fuel leakage or damage to the engine or emission system.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Pioneer S-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 107-2102 109-3148 109-6014 116-1119 116-1496 116-3303 116-6363 116-4430 Specifications Model NumbersSystems Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckOverall Width DimensionsOverall Length Overall HeightProduct Overview Curb WeightTorque Requirements Wheel Base Center of Caster Tire to Center of Drive TireControls OperationHour Meter Drive Wheel Release ValvesFuel Shut-Off Valve Pre-Start PTO Engagement SwitchDeck Lift Pedal Transport LockOperating Instructions Raise the Rollover Protection System RopsOpen the Fuel Shut-Off Valve Engaging the PTO Starting the EngineDisengaging the PTO Stopping the EngineDriving Forward Adjusting the Anti-Scalp Rollers Adjusting the Cutting HeightTransporting Transporting a UnitLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Battery Charge Recommended Jump Starting ProcedureCheck Engine Oil Level Check Mower Blades Do Not jump start a weak battery if these conditions existService Dealer Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareLubricate Grease Fittings Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Caster Wheel HubsCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Check Spark Arrester if equipped Copper-Based Anti-seize Thread Locking AdhesivesDielectric Grease Deck LevelingInch Deck Adjusting the Blade SlopeAdjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Full Forward Tracking Adjustment Motion Control Handle AdjustmentMotion Control Linkage Adjustment Removing the Shim Adjusting the Seat Ride SuspensionBrake mounting bolt Shim Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Clean Debris From MachineBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Electrical Diagram SchematicsElectrical Logic Schematic Pioneer S-Series Turf Equipment Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents