Exmark 000 & higher, 312 Motion Control Handle Adjustment, Full Forward Tracking Adjustment

Page 38

Maintenance

 

 

Figure 29

 

1.

Hairpin

3.

Yoke

2.

Clevis pin

4.

Jam nut

Adjusting the Brake to Engage: Shorten the linkage by turning the yoke clockwise.

Adjusting the Brake to Disengage: Lengthen the linkage by turning the yoke counterclockwise.

8.Reinstall the clevis pin and hair pin and tighten down the jam nut. Repeat step 6 and readjust if necessary.

9.When adjustment is complete, remove the jack stands or equivalent support and lower the machine.

10.Place the machine into the “operating” position. Refer to the Drive Wheel Release Valves section in Operation.

Motion Control Handle Adjustment

Adjusting the height:

The motion control levers can be adjusted higher or lower for maximum operator comfort.

1.Remove the hardware holding the control lever to the control arm shaft (Figure 30).

Figure 30

1.

Bolts

4.

Control arm shaft

2.

Washer

5.

Slotted hole

3.Control lever

2.Move the control lever to the next set of holes. Secure the lever with the hardware.

3.Repeat the adjustment for the opposite control lever.

Adjusting the Tilt

The motion control levers can be tilted fore or aft for maximum operator comfort.

1.Loosen the upper bolt holding the control lever to the control arm shaft.

2.Loosen the lower bolt just enough to pivot the control lever fore or aft Figure 30. Tighten both bolts to secure the control in the new position.

3.Repeat the adjustment for the opposite control lever.

Full Forward Tracking Adjustment

If the machine travels or pulls to one side when the motion control levers are in the full forward position, adjust the cover plates.

1.Loosen the screws on a cover plate (see Figure 31).

2.Slide the cover plate backward or forward to adjust the travel of the lever and tighten the screws.

3.Drive the machine and check the full forward tracking.

4.Repeat steps 1 through 3 until desired tracking is obtained.

38

Image 38
Contents Pioneer S-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 107-2102 109-3148 109-6014 116-1119 116-1496 116-3303 116-6363 116-4430 Systems SpecificationsModel Numbers Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckOverall Length DimensionsOverall Width Overall HeightTorque Requirements Curb WeightProduct Overview Wheel Base Center of Caster Tire to Center of Drive TireOperation ControlsFuel Shut-Off Valve Hour MeterDrive Wheel Release Valves Deck Lift Pedal PTO Engagement SwitchPre-Start Transport LockOpen the Fuel Shut-Off Valve Operating InstructionsRaise the Rollover Protection System Rops Disengaging the PTO Starting the EngineEngaging the PTO Stopping the EngineDriving Forward Adjusting the Cutting Height Adjusting the Anti-Scalp RollersLoading a Unit TransportingTransporting a Unit Maintenance Recommended Maintenance SchedulesCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions exist Check Mower BladesCheck Safety Interlock System Service DealerCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareCheck Tire Pressures Check Hydraulic Oil LevelLubricate Grease Fittings Lubricate Caster Wheel HubsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter Check Spark Arrester if equipped Dielectric Grease Thread Locking AdhesivesCopper-Based Anti-seize Deck LevelingAdjusting the Blade Slope Inch DeckDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Motion Control Handle Adjustment Full Forward Tracking AdjustmentMotion Control Linkage Adjustment Adjusting the Seat Ride Suspension Removing the ShimBrake mounting bolt Shim Clean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Schematics Electrical DiagramElectrical Logic Schematic Pioneer S-Series Turf Equipment Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.