Exmark 000 & higher, 312 manual Troubleshooting, Problem Possible Cause Corrective Action

Page 44

Troubleshooting

Troubleshooting

Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mower use.

When a problem occurs, do not overlook the simple causes. For example: starting problems could be caused by an empty fuel tank.

The following table lists some of the common causes of trouble. Do not attempt to service or replace major items or any items that call for special timing of adjustment procedures (such as valves, governor, etc.). Have this work done by your Engine Service Dealer.

Note: When disconnecting electrical connectors DO NOT pull on the wires to separate the connectors.

Problem

 

Possible Cause

 

Corrective Action

 

 

 

 

 

Starter does not crank

1.

PTO is engaged.

1.

Disengage the PTO.

 

2.

Parking brake is not engaged.

2.

Set the parking brake.

 

3.

Drive levers are not in neutral lock

3.

Ensure the drive levers are in the neutral

 

 

position.

 

lock position.

 

4.

Battery does not have a full charge.

4.

Charge the battery. See Check

 

 

 

 

Battery Charge and Recommended

 

 

 

 

Jump Starting Procedure sections in

 

 

 

 

Maintenance.

 

5.

Electrical connections are corroded, loose

5.

Check the electrical connections for

 

 

or faulty.

 

good contact. Clean connector terminals

 

 

 

 

thoroughly with electrical contact cleaner,

 

 

 

 

apply dielectric grease and reconnect.

 

6.

Fuse is blown.

6.

Replace the blown fuse.

 

7.

Relay or switch is defective.

7.

Contact an Authorized Service Dealer.

 

8.

Faulty module.

8.

Replace module.

 

 

 

 

 

Engine will not start, starts hard, or fails to

1.

Fuel tank is empty.

1.

Fill the fuel tank.

keep running

2.

Fuel shutoff valve is closed.

2.

Open the fuel shutoff valve.

 

 

3.

Oil level in the crankcase is low.

3.

Add oil to the crankcase.

 

4.

The throttle and choke are not in the

4.

Be sure the throttle control is midway

 

 

correct position.

 

between the “SLOW” and “FAST”

 

 

 

 

positions, and the choke is in the “ON”

 

 

 

 

position for a cold engine or the “OFF”

 

 

 

 

position for a warm engine.

 

5.

Dirt in fuel filter.

5.

Replace the fuel filter.

 

6.

Dirt, water, or stale fuel is in the fuel

6.

Contact an Authorized Service Dealer.

 

 

system.

 

 

 

7.

Air cleaner is dirty.

7.

Clean or replace the air cleaner element.

 

8.

Seat switch is not functioning properly.

8.

Check the seat switch indicator. Replace

 

 

 

 

seat if needed.

 

9.

Electrical connections are corroded, loose

9.

Check the electrical connections for

 

 

or faulty.

 

good contact. Clean connector terminals

 

 

 

 

thoroughly with electrical contact cleaner,

 

 

 

 

apply dielectric grease and reconnect.

 

10.

Relay or switch is defective.

10.

Contact an Authorized Service Dealer.

 

11.

Faulty spark plug.

11.

Clean, adjust or replace spark plug.

 

12.

Spark plug wire is not connected.

12.

Check the spark plug wire connection.

 

13.

Faulty module.

13.

Replace module.

 

 

 

 

 

44

Image 44
Contents Pioneer S-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationUsing the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 107-2102 109-3148 109-6014 116-1119 116-1496 116-3303 116-6363 116-4430 Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Overall WidthOverall Length Overall HeightCurb Weight Product OverviewTorque Requirements Wheel Base Center of Caster Tire to Center of Drive TireOperation ControlsFuel Shut-Off Valve Hour MeterDrive Wheel Release Valves PTO Engagement Switch Pre-StartDeck Lift Pedal Transport LockOpen the Fuel Shut-Off Valve Operating InstructionsRaise the Rollover Protection System Rops Starting the Engine Engaging the PTODisengaging the PTO Stopping the EngineDriving Forward Adjusting the Cutting Height Adjusting the Anti-Scalp RollersLoading a Unit TransportingTransporting a Unit Maintenance Recommended Maintenance SchedulesCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions exist Check Mower BladesCheck Safety Interlock System Service DealerService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareCheck Hydraulic Oil Level Lubricate Grease FittingsCheck Tire Pressures Lubricate Caster Wheel HubsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter Check Spark Arrester if equipped Thread Locking Adhesives Copper-Based Anti-seizeDielectric Grease Deck LevelingAdjusting the Blade Slope Inch DeckDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Motion Control Handle Adjustment Full Forward Tracking AdjustmentMotion Control Linkage Adjustment Adjusting the Seat Ride Suspension Removing the ShimBrake mounting bolt Shim Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Schematics Electrical DiagramElectrical Logic Schematic Pioneer S-Series Turf Equipment Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.