Exmark 0, 312 manual Seat, Hydrostatic Ground Drive System

Page 17

Specifications

Moving motion control levers outward (in slots) locks the drive system in neutral.

PTO Engagement Switch: Engages electric clutch (to drive belt) which engages mower blades.

Parking Brake Lever: Engages/Disengages parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Pedal: Foot pedal that lifts deck.

Transport Lock:

Latching position: Automatically latches at the transport position.

Unlatching position: Deck does not latch at the transport position.

Seat

Type:

For all units except LZX801KA606SS, LZX940KC606, LZX940KC726, LZX980KC606, LZX980KC726: Standard seat with high back, extra wide foam padded seat cushion with internal suspension, thick bolstering, two-tone cover, armrests, integral safety switch, and seat vibration isolation system.

Optional seat accessories for units with standard seats:

Custom ride suspension system to enhance Standard Seat. Adds approximately 3 inches (7.6 cm) to seat height.

Deluxe suspension (adjustable spring suspension) seat with high back, armrests, and integral safety switch. Seat height remains the same.

For LZX801KA606SS, LZX940KC606, LZX940KC726, LZX980KC606, LZX980KC726:

Deluxe suspension (adjustable spring suspension) seat with high back, armrests, and integral safety switch. Seat height remains the same.

Mounting: Hinged seat frame to tilt up seat. Held in tilted position with prop rod. Adjustable fore and aft on seat tracks.

Armrests:

Standard seat: foam padded adjustable flip-up armrests.

Suspension seat: molded adjustable flip-up armrests.

Seat Safety Switch:

Integrated seat switch. Time delay seat switch eliminates rough ground cut-outs.

Hydrostatic Ground Drive System

Two unitized hydrostatic transmissions:

48 and 52 inch decks:

12cc Parker axial piston pump

240cc Parker geroler motor

60 and 72 inch decks:

16cc Parker axial piston pump

280cc Ross geroler motor

Hydraulic Oil Type: Exmark Premium Hydro Oil.

Hydraulic Oil Capacity: 52 oz (1.5 L) per side

Hydraulic Filter: P/N 116-0164

Speeds:

12cc

0-10 mph (16.1 km/hr) forward.

0-5.5 mph (8.9 km/hr) reverse.

16cc

0-11.5 mph (18.5 km/hr) forward.

0-6 mph (9.7 km/hr) reverse.

Drive wheel release valves allow machine to be moved when engine is not running.

17

Image 17
Contents Lazer Z X-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Systems SpecificationsModel Numbers Hydrostatic Ground Drive System SeatTires & Wheels DimensionsCutting Deck Overall WidthAccessory Weight Table Worksheet Curb WeightOverall Height Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationHour Meter Ignition SwitchFuel Shut-Off Valve Fuel GaugeLow Voltage Indicator PTO Engagement SwitchDrive Wheel Release Valves Deck Lift PedalOperating Instructions Electronic Control Unit Malfunction IndicatorPre-Start Raise the Rollover Protection System RopsStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTODriving Forward Driving the MachineDriving in Reverse Adjusting the Cutting HeightTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemService Air Cleaner Check Air Filter Assembly if equippedCheck Seat Belt Check for Loose HardwareCheck Condition Of Belts Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Caster Wheel Hubs Lubricate Grease FittingsCheck Spark Plugs Lubricate Deck Lift PivotChange Fuel Filter Change Hydraulic System Filter and FluidCheck Spark Arrester if equipped Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Mobil HTS Grease Or Food-Grade Anti-seizeDeck Leveling Copper-Based Anti-seizeDielectric Grease 4 inches 8.3 cm Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Left Hand Brake Shown Electric Clutch AdjustmentMotion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentCaster Pivot Bearings Pre-Load Adjustment Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Guards Clean Debris From MachineMotor Oil Disposal Battery DisposalWaste Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram All units except Kohler EFI SchematicsRED Electrical Diagram Kohler EFIElectrical Logic Schematic All units except Kohler EFI Electrical Logic Schematic Kohler EFI SchematicsHydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb

0, 312 specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.