Exmark 312, 0 manual Motion Control Linkage, Adjustment

Page 44

Maintenance

Figure 33

1. Brake mounting bolt

2. Shim

B.Using needle nose pliers, or by hand, take hold of the tab and remove the shim (Do Not discard the shim until proper clutch function has been confirmed).

C.Using a pneumatic line, blow out any debris from under the brake pole and around the brake spacers.

D.Re-torque each bolt (M6 x 1) to 10 ft-lb (13 N-m) +/-0.5 ft-lb (0.7 N-m).

E.Using a 0.010 inch thick feeler gauge, verify that a gap is present between the rotor and armature face on both sides of the brake pole as shown. (Due to the way the rotor and armature faces wear (peaks and valleys) it is sometimes difficult to measure the true gap.)

Figure 35

1.Feeler gauge

•If the gap is less than 0.010 inch, then reinstall the shim and reference the Troubleshooting section.

•If the gap is sufficient, proceed to the safety check in step F.

F.Perform the following safety check:

a.Sit on the seat and start the engine.

b.Make sure the blades Do Not engage with the PTO switch “off ” and the clutch disengaged.

If the clutch does not disengage, reinstall the shim and reference the Troubleshooting section.

c.Engage and disengage the PTO switch ten consecutive times to ensure the clutch is functioning properly. If the clutch does not engage properly, reference the Troubleshooting section.

1

Figure 34

1.Feeler gauge

G011733

Motion Control Linkage

 

 

Adjustment

 

Located on either side of the fuel tank, below the seat

 

are the pump control linkages. Rotating the pump

 

linkage with a 1/2 inch wrench allows fine tuning

 

adjustments so that the machine does not move in

 

neutral. Any adjustments should be made for neutral

 

positioning only.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Lazer Z X-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemDimensions Tires & WheelsCutting Deck Overall WidthCurb Weight Accessory Weight Table WorksheetOverall Height Tread Width Center to Center of Tires, WidthwiseProduct Overview Torque RequirementsOperation ControlsIgnition Switch Hour MeterFuel Shut-Off Valve Fuel GaugePTO Engagement Switch Low Voltage IndicatorDrive Wheel Release Valves Deck Lift PedalElectronic Control Unit Malfunction Indicator Operating InstructionsPre-Start Raise the Rollover Protection System RopsOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTODriving the Machine Driving ForwardAdjusting the Cutting Height Driving in ReverseTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck Air Filter Assembly if equipped Service Air CleanerCheck Seat Belt Check for Loose HardwareCheck Condition Of Belts Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Check Spark PlugsChange Fuel Filter Change Hydraulic System Filter and FluidWheel Hub Slotted Nut Torque Specification Check Spark Arrester if equippedThread Locking Adhesives Mobil HTS Grease Or Food-Grade Anti-seizeDeck Leveling Copper-Based Anti-seizeDielectric Grease 4 inches 8.3 cm Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Electric Clutch Adjustment Left Hand Brake ShownAdjustment Motion Control LinkageMotion Control Damper Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Guards Clean Debris From MachineMotor Oil Disposal Battery DisposalWaste Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Diagram All units except Kohler EFIElectrical Diagram Kohler EFI REDElectrical Logic Schematic All units except Kohler EFI Schematics Electrical Logic Schematic Kohler EFIHydraulic Diagram General Warranty Conditions and Products Covered Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb

0, 312 specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents