Exmark 0, 312 manual Wheel Hub Slotted Nut Torque Specification, Check Spark Arrester if equipped

Page 39

Maintenance

8.Install the new filters and torque to 14 ft-lb (19 N-m).

9.Fill the hydraulic system as stated in Check Hydraulic Oil Level section.

Exmark Premium Hydro Oil is recommended. Refer to the chart for an acceptable alternative:

Hydro Oil

Service Interval

 

 

Exmark Premium Hydro

After first 250 hours

Oil (Preferred)

*Every 500 hours

 

thereafter

Mobil 1 15W50

After first 250 hours

 

*Every 250 hours

 

thereafter

*May need more often under severe conditions.

10.Remove the catch pan and properly dispose of hydro oil and filter according to local codes.

11.Re-install the pump drive belt.

12.Start engine and move throttle control ahead to full throttle position. Move the speed control levers to the full speed and run for one minute. Shut down the machine, allow the hydros to cool and recheck oil level.

13.Remove the jack stands.

Note: Do Not change the hydraulic system oil (except for what can be drained when changing filter), unless it is felt the oil has been contaminated or been extremely hot.

Changing oil unnecessarily could damage hydraulic system by introducing contaminants into the system.

Wheel Hub - Slotted Nut Torque Specification

Service Interval: After the first 100 hours

Every 500 hours thereafter

Torque the slotted nut to 211-260 ft-lb (286-352 N-m).

Note: Do Not use anti-seize on wheel hub.

Check Spark Arrester (if equipped)

Service Interval: Every 50 hours

WARNING

Hot exhaust system components may ignite gasoline vapors even after the engine is stopped. Hot particles exhausted during engine operation may ignite flammable materials. Fire may result in personal injury or property damage.

Do Not refuel or run engine unless spark arrester is installed.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Wait for muffler to cool.

3.If any breaks in the screen or welds are observed, replace arrester.

4.If plugging of the screen is observed, remove arrester and shake loose particles out of the arrester and clean screen with a wire brush (soak in solvent if necessary). Reinstall arrester on exhaust outlet.

Thread Locking Adhesives

Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type” are used on the following fasteners:

ROPS spring pin housing.

Hydro pump control arm, linkage bolt, and attachment bolt.

Hydro cooling fan screw.

Hydro park brake cable anchor mounting bolt

Sheave and clutch retaining bolt in the end of engine crankshaft.

Thread locking adhesives are required for some hardware on engines — see the Engine manual.

Mobil HTS Grease (Or Food-Grade Anti-seize)

Mobil HTS grease (or food-grade anti-seize) is used in the following locations:

Between the jackshaft and bearings.

Between the jackshaft and sheaves, spindles, and bearings.

39

Image 39
Contents Lazer Z X-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Specifications Model NumbersSystems Hydrostatic Ground Drive System SeatOverall Width DimensionsTires & Wheels Cutting DeckTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet Overall HeightTorque Requirements Product OverviewControls OperationFuel Gauge Ignition SwitchHour Meter Fuel Shut-Off ValveDeck Lift Pedal PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesRaise the Rollover Protection System Rops Electronic Control Unit Malfunction IndicatorOperating Instructions Pre-StartDisengaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Engaging the PTODriving Forward Driving the MachineDriving in Reverse Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers TransportingTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemCheck for Loose Hardware Check Air Filter Assembly if equippedService Air Cleaner Check Seat BeltCheck Hydraulic Oil Level Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel Hubs Lubricate Grease FittingsChange Hydraulic System Filter and Fluid Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterMobil HTS Grease Or Food-Grade Anti-seize Wheel Hub Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseDeck Leveling 4 inches 8.3 cm Adjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Left Hand Brake Shown Electric Clutch AdjustmentMotion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsBattery Disposal Waste DisposalMotor Oil Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram All units except Kohler EFI SchematicsRED Electrical Diagram Kohler EFIElectrical Logic Schematic All units except Kohler EFI Electrical Logic Schematic Kohler EFI SchematicsHydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb

0, 312 specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.