Exmark 0, 312 manual Operation

Page 7

Safety

CAUTION

Fuel tank vent is located inside the roll bar tube. Removing or modifying the roll bar could result in fuel leakage and violate emissions regulations.

Do Not remove roll bar.

Do Not weld, drill, or modify roll bar in any way.

Check that the operator's presence controls, safety switches, and shields are attached and functioning properly. Do Not operate unless they are functioning properly.

Operation

WARNING

Operating engine parts, especially the muffler, become extremely hot. Severe burns can occur on contact and debris, such as leaves, grass, brush, etc. can catch fire.

Allow engine parts, especially the muffler, to cool before touching.

Remove accumulated debris from muffler and engine area.

Install and maintain in working order a spark arrester before using equipment on forest-covered, grass-covered, or brush-covered unimproved land.

WARNING

Engine exhaust contains carbon monoxide, which is an odorless deadly poison that can kill you.

Do Not run engine indoors or in a small confined area where dangerous carbon monoxide fumes can collect.

Operate only in daylight or good artificial light, keeping away from holes and hidden hazards.

Be sure all drives are in neutral and parking brake is engaged before starting engine. Use seat belts with the roll bar in the raised and locked position.

Never operate the mower with damaged guards, shields, or covers. Always have safety shields, guards, switches and other devices in place and in proper working condition.

Never mow with the discharge deflector raised, removed or altered unless there is a grass collection system or mulch kit in place and working properly.

Do Not change the engine governor setting or overspeed the engine.

Park machine on level ground. Stop engine, wait for all moving parts to stop, remove key and engage parking brake:

Before checking, cleaning or working on the mower.

After striking a foreign object or abnormal vibration occurs (inspect the mower for damage and make repairs before restarting and operating the mower).

Before clearing blockages.

Whenever you leave the mower.

Stop engine, wait for all moving parts to stop, and engage parking brake:

Before refueling.

Before dumping the grass catcher.

WARNING

Hands, feet, hair, clothing, or accessories can become entangled in rotating parts. Contact with the rotating parts can cause traumatic amputation or severe lacerations.

Do Not operate the machine without guards, shields, and safety devices in place and working properly.

Keep hands, feet, hair, jewelry, or clothing away from rotating parts.

NEVER carry passengers. DO NOT operate the mower when people, especially children, or pets are in the area.

Be alert, slow down and use caution when making turns. Look behind and to the side before changing directions.

Stop the blades, slow down, and use caution when crossing surfaces other than grass and when transporting the mower to and from the area to be mowed.

Be aware of the mower discharge path and direct discharge away from others.

7

Image 7
Contents Lazer Z X-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System SeatOverall Width DimensionsTires & Wheels Cutting DeckTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet Overall HeightTorque Requirements Product OverviewControls OperationFuel Gauge Ignition SwitchHour Meter Fuel Shut-Off ValveDeck Lift Pedal PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesRaise the Rollover Protection System Rops Electronic Control Unit Malfunction IndicatorOperating Instructions Pre-StartDisengaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Engaging the PTODriving Forward Driving the MachineDriving in Reverse Adjusting the Cutting HeightTransporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemCheck for Loose Hardware Check Air Filter Assembly if equippedService Air Cleaner Check Seat BeltCheck Tire Pressures Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Caster Wheel Hubs Lubricate Grease FittingsChange Hydraulic System Filter and Fluid Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterMobil HTS Grease Or Food-Grade Anti-seize Wheel Hub Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Thread Locking AdhesivesDielectric Grease Copper-Based Anti-seizeDeck Leveling 4 inches 8.3 cm Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Left Hand Brake Shown Electric Clutch AdjustmentMotion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling GuardsWaste Disposal Battery DisposalMotor Oil Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram All units except Kohler EFI SchematicsRED Electrical Diagram Kohler EFIElectrical Logic Schematic All units except Kohler EFI Electrical Logic Schematic Kohler EFI SchematicsHydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb

0, 312 specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.