Exmark 0, 312 manual Operation, Controls

Page 21

Operation

Operation

Note: Determine the left and right sides of the machine from the normal operating position.

Controls

Motion Control Levers

The motion control levers located on each side of the console control the forward and reverse motion of the machine.

Moving the levers forward or backward turns the wheel on the same side forward or reverse respectively. Wheel speed is proportional to the amount the lever is moved.

Moving the levers outward from the center position into the T-slot locks them in the neutral position (Figure 5).

When the motion control levers are in the neutral position, the LCD indicator appears in the message display on the RH console (see Figure 8).

Choke Control (All Units Except Kohler EFI)

Located on right console (black lever) (see Figure 6).

The choke is used to aid in starting a cold engine. Moving the choke lever forward will put the choke in the “ON” position and moving the choke lever to the rear, to the detent, will put the choke in the “OFF” position. Do Not run a warm engine with choke in the “ON” position.

Figure 6

Right Console

1.

Fuses

4.

PTO engagement switch

2.

Message display

5.

Throttle

3.

Ignition switch

6.

Choke

 

 

 

 

Figure 5

1.

Neutral lock position

4.

Forward

 

(handles out)

 

 

2.

Neutral operate position

5.

Neutral (operate)

 

(handles in)

 

 

3.

Front of Unit

6.

Reverse

 

 

 

 

Throttle Control

Located on right console (red lever) (see Figure 6).

The throttle is used to control engine speed. Moving the throttle lever forward will increase engine speed and moving the throttle lever to the rear will decrease engine speed. Moving the throttle forward into the detent is full throttle.

Brake Lever

Located on right side of unit, just to the front of the RH motion control lever.

The brake lever engages a parking brake on the drive wheels.

Note: The LCD indicator appears in the message display on the RH console when the park brake is engaged (see Figure 8).

Pull the lever up and rearward to engage the brake.

21

Image 21
Contents Lazer Z X-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Specifications Model NumbersSystems Hydrostatic Ground Drive System SeatTires & Wheels DimensionsCutting Deck Overall WidthAccessory Weight Table Worksheet Curb WeightOverall Height Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationHour Meter Ignition SwitchFuel Shut-Off Valve Fuel GaugeLow Voltage Indicator PTO Engagement SwitchDrive Wheel Release Valves Deck Lift PedalOperating Instructions Electronic Control Unit Malfunction IndicatorPre-Start Raise the Rollover Protection System RopsStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Disengaging the PTODriving Forward Driving the MachineDriving in Reverse Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers TransportingTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemService Air Cleaner Check Air Filter Assembly if equippedCheck Seat Belt Check for Loose HardwareCheck Hydraulic Oil Level Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel Hubs Lubricate Grease FittingsCheck Spark Plugs Lubricate Deck Lift PivotChange Fuel Filter Change Hydraulic System Filter and FluidCheck Spark Arrester if equipped Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Dielectric GreaseDeck Leveling 4 inches 8.3 cm Adjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Left Hand Brake Shown Electric Clutch AdjustmentMotion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentCaster Pivot Bearings Pre-Load Adjustment Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Guards Clean Debris From MachineBattery Disposal Waste DisposalMotor Oil Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram All units except Kohler EFI SchematicsRED Electrical Diagram Kohler EFIElectrical Logic Schematic All units except Kohler EFI Electrical Logic Schematic Kohler EFI SchematicsHydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb

0, 312 specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.