Exmark 000 & higher, 312 Dimensions, Cutting Deck, Overall Width, Overall Length, Overall Height

Page 18

Specifications

Size

13 x 6.50-6

 

 

Ply Rating

4

 

 

Pressure

N/A

Cutting Deck

Cutting Width:

48 inch Deck: (121.9 cm)

52 inch Deck: (132.1 cm)

60 inch Deck: (152.4 cm)

72 inch Deck: (182.9 cm)

Discharge: Side

Blade Size: (3 ea.)

48 inch Deck: 16.25 inches (41.3 cm)

52 inch Deck: 18.00 inches (45.7 cm)

60 inch Deck: 20.50 inches (52.1 cm)

72 inch Deck: 24.50 inches (62.2 cm)

Blade Spindles: Solid steel spindles with 1.00 inch (25 mm) I.D. bearings.

Deck Drive: Electric clutch:

48 and 52 inch Decks: “B” Section belt with self-tensioning idler.

60 and 72 inch Decks: 5V Section belt with self-tensioning idler.

Deck:

Full floating deck is attached to out-front support frame. Anti-scalp rollers provide maximum turf protection. Deck design allows for bagging, mulching or side discharge.

48 inch Deck: 3 anti-scalp rollers

52 inch Deck: 3 anti-scalp rollers

60 inch Deck: 4 anti-scalp rollers

72 inch Deck: 6 anti-scalp rollers

Deck Depth:

48 inch Deck: 5.5 inches (14 cm)

52 inch Deck: 5.5 inches (14 cm)

60 inch Deck: 5.5 inches (14 cm)

72 inch Deck: 5.5 inches (14 cm)

Cutting Height Adjustment:

Foot activated lever is used to adjust the cutting height from 1 inch (2.5 cm) to 5 1/2 inches (14 cm) in 1/4 inch (6.4 mm) increments.

Mulching Kit: Optional.

Dimensions

Overall Width:

 

48 inch Deck

52 inch Deck

Without Deck

45.7

inches

45.7

inches

 

(116.1 cm)

(116.1 cm)

Deflector Up

51.8

inches

56.3

inches

 

(131.6 cm)

(143.0 cm)

Deflector Down

59.6

inches

64.8

inches

 

(151.4 cm)

(164.6 cm)

 

60 inch Deck

72 inch Deck

Without Deck

53.0

inches

59.1

inches

 

(134.6 cm)

(150.1 cm)

Deflector Up

62.5

inches

73.5

inches

 

(158.8 cm)

(186.7 cm)

Deflector Down

72.8

inches

84.9

inches

 

(184.9 cm)

(215.6 cm)

Overall Length:

 

48 inch Deck

52 inch Deck

Roll Bar - Up

79.2

inches

79.2 inches

 

(201.2 cm)

(201.2 cm)

Roll Bar - Down

80.9

inches

80.9 inches

 

(205.5 cm)

(205.5 cm)

 

60 inch Deck

72 inch Deck

Roll Bar - Up

83.1

inches

86.1

inches

 

(211.1 cm)

(218.7 cm)

Roll Bar - Down

84.8

inches

87.8

inches

 

(215.4 cm)

(223.0 cm)

Overall Height:

Roll Bar - Up

Roll Bar - Down

70.5 inches (179.1 cm)

46.8 inches (118.9 cm)

 

 

18

Image 18
Contents Lazer Z S-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Specifications Model NumbersSystems Seat Hydrostatic Ground Drive SystemTires and Wheels Overall Width DimensionsCutting Deck Overall LengthCurb Weight Tread Width Center to Center of Tires, WidthwiseWheel Base Center of Caster Tire to Center of Drive Tire Accessory Weight Table Worksheet Torque RequirementsControls Product OverviewOperation Motion Control LeversThrottle Control Ignition SwitchChoke Control All Units Except Kohler EFI Brake LeverFuel Shut-Off Valve Fuel GaugeDrive Wheel Release Valves Pre-Start Open the Fuel Shut-Off Valve Operating InstructionsRaise the Rollover Protection System Rops Starting the EngineStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineDriving Forward Adjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck for Loose Hardware Service Air CleanerCheck Seat Belt Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Check Spark Plugs Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Change Fuel FilterWheel Hub Slotted Nut Torque Specification Change Hydraulic System Filter and FluidCheck Spark Arrester if equipped Dielectric Grease Thread Locking AdhesivesCopper-Based Anti-seize Deck Leveling4 inches 8.3 cm Adjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Electric Clutch Adjustment Left Hand Brake ShownAdjustment Motion Control LinkageMotion Control Damper Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Diagram All units except Kohler EFIElectrical Diagram Kohler EFI REDSchematics Electrical Logic Schematic All units except Kohler EFIStart Relay REG MAG Lamp Hydraulic Diagram General Warranty Conditions and Products Covered Page This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.