Exmark 000 & higher, 312 manual See Drive Wheel Release Valves section

Page 50

Troubleshooting

Problem

 

Possible Cause

 

Corrective Action

 

 

 

 

 

Engine loses power

1.

Engine load is excessive

1.

Reduce the ground speed.

 

2.

Air cleaner is dirty.

2.

Clean or replace the air cleaner element.

 

3.

Oil level in the crankcase is low.

3.

Add oil to the crankcase.

 

4.

Cooling fins and air passages for the

4.

Remove the obstructions from the cooling

 

 

engine are plugged.

 

fins and air passages.

 

5.

Dirt in fuel filter.

5.

Replace the fuel filter.

 

6.

Dirt, water, or stale fuel is in the fuel

6.

Contact an Authorized Service Dealer.

 

 

system.

 

 

 

 

 

 

 

Mower pulls left or right (with levers fully

1.

Tire pressure in drive tires not correct.

1.

Adjust tire pressure in the drive tires.

forward)

 

 

 

 

 

 

 

 

 

Machine does not drive

1.

Drive release handle not in “operating”

1.

Position handle in “operating” position;

 

 

position.

 

see Drive Wheel Release Valves section

 

 

 

 

in Operation.

 

2.

Drive or pump belt is worn, loose or

2.

Change the belt.

 

 

broken.

 

 

 

3.

Drive or pump belt is off a pulley.

3.

Change the belt.

 

4.

Broken or missing idler spring.

4.

Replace the spring.

 

5.

Hydraulic fluid level is low or too hot.

5.

Add hydraulic fluid to reservoir or let it

 

 

 

 

cool down.

 

 

 

 

 

Uneven cutting height.

1.

Blade(s) not sharp.

1.

Sharpen the blade(s).

 

2.

Cutting blade(s) is/are bent.

2.

Install new cutting blade(s).

 

3.

Mower deck is not level.

3.

Level mower deck from side-to-side and

 

 

 

 

front-to-rear.

 

4.

Underside of mower is dirty.

4.

Clean the underside of the mower.

 

5.

Tire pressure in drive tires not correct.

5.

Adjust tire pressure in the drive tires.

 

6.

Blade spindle bent.

6.

Contact an Authorized Service Dealer.

 

7.

Tips of adjacent blades are at an uneven

7.

Replace blades, spindles and (or) check

 

 

cutting height. Blades tips should be even

 

for damage to mower deck.

 

 

within 3/16 inch which is approximately

 

 

 

 

one blade thickness.

 

 

 

 

 

 

 

Abnormal vibration

1.

Cutting blade(s) is/are bent or unbalanced.

1.

Install new cutting blade(s).

 

2.

Blade mounting bolt is loose.

2.

Tighten the blade mounting bolt.

 

3.

Engine mounting bolts are loose.

3.

Tighten the engine mounting bolts.

 

4.

Loose engine pulley, idler pulley, or blade

4.

Tighten the appropriate pulley.

 

 

pulley.

 

 

 

5.

Engine pulley is damaged.

5.

Contact an Authorized Service Dealer.

 

6.

Blade spindle is bent.

6.

Contact an Authorized Service Dealer.

 

7.

Belt is damaged.

7.

Install new belt.

 

 

 

 

 

Blades do not rotate.

1.

Deck belt is worn, loose or broken.

1.

Install new deck belt.

 

2.

Deck belt is off pulley.

2.

Install belt on clutch and deck pulleys,

 

 

 

 

idlers, and tensioning idler per routing

 

 

 

 

decal on deck.

 

3.

Broken or missing idler spring.

3.

Replace the spring.

 

4.

Drive belt not routed correctly.

4.

Refer to belt routing decal on deck.

 

 

 

 

 

50

Image 50
Contents Lazer Z S-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Systems SpecificationsModel Numbers Tires and Wheels SeatHydrostatic Ground Drive System Overall Width DimensionsCutting Deck Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightTread Width Center to Center of Tires, Widthwise Accessory Weight Table Worksheet Torque RequirementsControls Product OverviewOperation Motion Control LeversThrottle Control Ignition SwitchChoke Control All Units Except Kohler EFI Brake LeverDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Pre-Start Open the Fuel Shut-Off Valve Operating InstructionsRaise the Rollover Protection System Rops Starting the EngineStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineDriving Forward Adjusting the Cutting Height Adjusting the Anti-Scalp RollersLoading a Unit TransportingTransporting a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck for Loose Hardware Service Air CleanerCheck Seat Belt Change Engine OilLubricate Grease Fittings Check Tire PressuresCheck Condition Of Belts Check Spark Plugs Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Change Fuel FilterCheck Spark Arrester if equipped Wheel Hub Slotted Nut Torque SpecificationChange Hydraulic System Filter and Fluid Dielectric Grease Thread Locking AdhesivesCopper-Based Anti-seize Deck Leveling4 inches 8.3 cm Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Electric Clutch Adjustment Left Hand Brake ShownAdjustment Motion Control LinkageMotion Control Damper Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Diagram All units except Kohler EFIElectrical Diagram Kohler EFI REDSchematics Electrical Logic Schematic All units except Kohler EFIStart Relay REG MAG Lamp Hydraulic Diagram General Warranty Conditions and Products Covered Page This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.