Exmark 000 & higher, 312 manual Recommended Maintenance Schedules

Page 30

Maintenance

Maintenance

Note: Determine the left and right sides of the machine from the normal operating position.

WARNING

While maintenance or adjustments are being made, someone could start the engine. Accidental starting of the engine could seriously injure you or other bystanders.

Remove the key from the ignition switch, engage parking brake, and pull the wire(s) off the spark plug(s) before you do any maintenance. Also push the wire(s) aside so it does not accidentally contact the spark plug(s).

WARNING

The engine can become very hot. Touching a hot engine can cause severe burns.

Allow the engine to cool completely before service or making repairs around the engine area.

Recommended Maintenance Schedule(s)

Maintenance Service

Maintenance Procedure

Interval

 

 

 

 

 

After the first 5 hours

•

Change the engine oil.

 

 

 

• Check the wheel hub slotted nut torque specifications.

After the first 100 hours

•

Check the wheel lug nuts.

 

• Check the park brake adjustment.

 

 

 

After the first 250 hours

•

Change the hydraulic filter and fluid.

 

 

 

• Check the engine oil level.

 

•

Check the mower blades.

 

• Check the safety interlock system.

 

• Check the rollover protections systems (roll bar) knobs.

Before each use or daily

• Check the seat belt.

•

Check for loose hardware.

 

 

• Clean the engine and exhaust system area.

 

• Clean the hydro fan cooling guards.

 

• Clean the grass and debris build-up from the machine and cutting deck.

 

• Clean the grass build-up from under the cutting deck.

 

 

 

• Check the hydraulic oil level.

Every 50 hours

• Check the tire pressures.

• Check the condition of the belts.

 

 

• Check spark arrester (if equipped).

 

 

 

• Change the engine oil. (May need more often under severe conditions.)

Every 100 hours

•

Lubricate the deck lift pivots.

 

• Remove the engine shrouds and clean the cooling fins.

 

 

 

Every 200 hours

•

Check the spark plugs.

 

 

 

• Replace the primary air cleaner element — check secondary air cleaner element; replace if

Every 250 hours

 

dirty. (May need more often under severe conditions. See the Engine Owner's Manual for

 

 

additional information.)

 

 

 

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Lazer Z S-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Specifications Model NumbersSystems Seat Hydrostatic Ground Drive SystemTires and Wheels Overall Width DimensionsCutting Deck Overall LengthCurb Weight Tread Width Center to Center of Tires, WidthwiseWheel Base Center of Caster Tire to Center of Drive Tire Accessory Weight Table Worksheet Torque RequirementsControls Product OverviewOperation Motion Control LeversThrottle Control Ignition SwitchChoke Control All Units Except Kohler EFI Brake LeverFuel Shut-Off Valve Fuel GaugeDrive Wheel Release Valves Pre-Start Open the Fuel Shut-Off Valve Operating InstructionsRaise the Rollover Protection System Rops Starting the EngineStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineDriving Forward Adjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting Transporting a UnitLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck for Loose Hardware Service Air CleanerCheck Seat Belt Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Check Spark Plugs Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Change Fuel FilterWheel Hub Slotted Nut Torque Specification Change Hydraulic System Filter and FluidCheck Spark Arrester if equipped Dielectric Grease Thread Locking AdhesivesCopper-Based Anti-seize Deck Leveling4 inches 8.3 cm Adjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Electric Clutch Adjustment Left Hand Brake ShownAdjustment Motion Control LinkageMotion Control Damper Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Diagram All units except Kohler EFIElectrical Diagram Kohler EFI REDSchematics Electrical Logic Schematic All units except Kohler EFIStart Relay REG MAG Lamp Hydraulic Diagram General Warranty Conditions and Products Covered Page This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents