Exmark 312, 000 & higher manual Caster Pivot Bearings Pre-Load Adjustment

Page 46

Maintenance

2.Slide the cover plate backward or forward to adjust the travel of the lever and tighten the screws.

3.Drive the machine and check the full forward tracking.

4.Repeat steps 1 through 3 until desired tracking is obtained.

Figure 40

1. Spring disc washers

Figure 39

RH Motion Control Shown

1. Screw

3. Motion control lever

2.Cover plate

Caster Pivot Bearings

Pre-Load Adjustment

Remove dust cap from caster and tighten nyloc nut until washers are flat and back off 1/4 of a turn to properly set the pre-load on the bearings. If disassembled, make sure the spring disc washers are reinstalled as shown in Figure 40.

46

Image 46
Contents Lazer Z S-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System SeatTires and Wheels Overall Width DimensionsCutting Deck Overall LengthTread Width Center to Center of Tires, Widthwise Curb WeightWheel Base Center of Caster Tire to Center of Drive Tire Accessory Weight Table Worksheet Torque RequirementsControls Product OverviewOperation Motion Control LeversThrottle Control Ignition SwitchChoke Control All Units Except Kohler EFI Brake LeverFuel Gauge Fuel Shut-Off ValveDrive Wheel Release Valves Pre-Start Open the Fuel Shut-Off Valve Operating InstructionsRaise the Rollover Protection System Rops Starting the EngineStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineDriving Forward Adjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting a Unit TransportingLoading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Check Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck for Loose Hardware Service Air CleanerCheck Seat Belt Change Engine OilCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Check Spark Plugs Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Change Fuel FilterChange Hydraulic System Filter and Fluid Wheel Hub Slotted Nut Torque SpecificationCheck Spark Arrester if equipped Dielectric Grease Thread Locking AdhesivesCopper-Based Anti-seize Deck Leveling4 inches 8.3 cm Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Electric Clutch Adjustment Left Hand Brake ShownAdjustment Motion Control LinkageMotion Control Damper Adjustment Motion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Diagram All units except Kohler EFIElectrical Diagram Kohler EFI REDSchematics Electrical Logic Schematic All units except Kohler EFIStart Relay REG MAG Lamp Hydraulic Diagram General Warranty Conditions and Products Covered Page This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.