Exmark 000 & higher, 312 manual Check Mower Blades

Page 33

Maintenance

Figure 19

1.Positive (+) cable on discharged battery

2.Positive (+) cable on booster battery

3.Negative (–) cable on the booster battery

4.Negative (–) cable on the engine block

5.Booster battery

6.Discharged battery

7.Engine block

Check Mower Blades

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lift deck and secure in raised position as stated in the Clean Grass Build-Up Under Deck section.

3.Inspect blades and sharpen or replace as required.

4.Reinstall the blades (if they were removed) in the following order:

A.Install bushing through blade with bushing flange on bottom (grass) side of blade.

4.Connect the other end of the positive cable to the positive terminal of the booster battery.

5.Connect the black negative (–) cable to the other terminal (negative) of the booster battery.

6.MAKE THE FINAL CONNECTION ON THE ENGINE BLOCK OF THE STALLED VEHICLE (NOT TO THE NEGATIVE POST) AWAY FROM THE BATTERY. STAND BACK (see Figure 20).

Figure 20

1.Engine block

2.Negative (–) cable

7.Start the vehicle and remove the cables in the reverse order of connection (the engine block (black) connection is the first to disconnect).

Figure 21

1.Install bushing in blade prior to installing bushing in spindle.

B.Install bushing/blade assembly into spindle. Make sure the splines on the bushing are engaged in the spindle before tightening the bolt.

Figure 22

1.Use wrench here for blade installation. This nut has been torqued to 130–160 ft-lb (176–217 N-m)

2.Torque to 50-60 ft-lb (68-81 N-m) Apply lubricant to threads as needed to prevent seizing. Copper-based anti-seize preferable. Grease acceptable substitute.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Lazer Z S-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-9361 116-1654 116-2643 116-2844 109-7069 Specifications Model NumbersSystems Seat Hydrostatic Ground Drive SystemTires and Wheels Cutting Deck DimensionsOverall Width Overall LengthCurb Weight Tread Width Center to Center of Tires, WidthwiseWheel Base Center of Caster Tire to Center of Drive Tire Torque Requirements Accessory Weight Table WorksheetOperation Product OverviewControls Motion Control LeversChoke Control All Units Except Kohler EFI Ignition SwitchThrottle Control Brake LeverFuel Shut-Off Valve Fuel GaugeDrive Wheel Release Valves Pre-Start Raise the Rollover Protection System Rops Operating InstructionsOpen the Fuel Shut-Off Valve Starting the EngineDisengaging the PTO Engaging the PTOStopping the Engine Driving the MachineDriving Forward Adjusting the Anti-Scalp Rollers Adjusting the Cutting HeightTransporting Transporting a UnitLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Check Rollover Protections Systems Roll Bar Knobs Check Safety Interlock SystemCheck Seat Belt Service Air CleanerCheck for Loose Hardware Change Engine OilCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Deck Lift Pivot Lubricate Caster Wheel HubsCheck Spark Plugs Change Fuel FilterWheel Hub Slotted Nut Torque Specification Change Hydraulic System Filter and FluidCheck Spark Arrester if equipped Copper-Based Anti-seize Thread Locking AdhesivesDielectric Grease Deck Leveling4 inches 8.3 cm Adjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Left Hand Brake Shown Electric Clutch AdjustmentMotion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentCaster Pivot Bearings Pre-Load Adjustment Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Clean Debris From MachineBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram All units except Kohler EFI SchematicsRED Electrical Diagram Kohler EFIElectrical Logic Schematic All units except Kohler EFI SchematicsStart Relay REG MAG Lamp Hydraulic Diagram General Warranty Conditions and Products Covered Page This page may be copied for personal use Exmark Accessories and Options
Related manuals
Manual 60 pages 29.4 Kb Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 23.73 Kb Manual 40 pages 46.04 Kb

0, 312, 000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents