Exmark 000 & higher manual Specifications, Model Numbers, Systems

Page 15

Specifications

Specifications

Model Numbers

Serial Nos: 790,000 and Higher

LZAS20BV484; LZAS20KC484; LZAS23KC524; LZAS25KC604; LZAS26LKA604; LZAS27KC524; LZAS27KC604; LZAS29KA724

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

RPM:

All units except LZAS20BV484 and LZAS20KC484: Full Speed: 3750 ±50 RPM (PTO not engaged) Idle: 1500 ±100 RPM

LZAS20BV484 and LZAS20KC484: Full

Speed: 3750 +0/-50 RPM (PTO not engaged)

Idle: 1500 ±100 RPM

Fuel System

Capacity: 12.0 gal. (45.4 L)

Type of Fuel: Regular unleaded gasoline, 87 octane or higher.

Fuel Filter:

Briggs & Stratton:

Briggs & Stratton P/N 691035

Kohler:

Kohler P/N 24 050 13

Kawasaki:

Kawasaki P/N 49019-7001

Fuel Shut-Off Valve:

All Units: 1/4 turn increments (“ON”, “OFF”).

Fuel level eight segment display — right hand control panel.

Low fuel indicator light.

Electrical System

Charging System: Flywheel Alternator

Charging Capacity:

Briggs & Stratton: 16 amps

Kohler and Kawasaki Air-Cooled: 15 amps

Kawasaki Liquid-Cooled: 20 amps

Battery Type: BCI Group U1

Recommended Minimum Battery CCA: 260 CCA

Battery Voltage: 12 Volt

Low Voltage Light — RH control panel

Polarity: Negative Ground

Fuses: All units:

25 amp main fuse

25 amp charging system fuse

10 amp PTO fuse

15 amp accessory fuse

Safety Interlock System

LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Cooling System (Kawasaki

Liquid-Cooled Only)

Fan: Continuous operation with engine running.

Coolant Liquid: 50/50 mix of DexCool© extended life antifreeze and water.

Coolant Capacity: 3.1 quarts

15

Image 15
Contents Lazer Z Advantage Series Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 116-0906 Specifications Model NumbersSystems Tires & Wheels Operator ControlsSeat Hydrostatic Ground Drive SystemOverall Height DimensionsOverall Width Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationIgnition Switch Hour MeterFuel Shut-Off Valve Drive Wheel Release Valves PTO Engagement SwitchLow Voltage Indicator Fuel GaugeTransport Lock Pre-StartOperating Instructions Deck Lift PedalOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTO Stopping the EngineDriving the Machine Driving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers TransportingTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Hydraulic Oil Level Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsWheel Hub Slotted Nut Torque Specification Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyDielectric Grease Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsDeck Removal Adjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Start the mower while in the operator position Motion Control Linkage Adjustment Electric Clutch AdjustmentMotion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Clutch Shim Caster Pivot Bearings Pre-Load AdjustmentRemoving the Shim Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Guards Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Troubleshooting Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledSchematics Electrical Logic Schematic Air-CooledLiquid Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.