Exmark 000 & higher Check Tire Pressures, Check Condition Of Belts, Lubricate Grease Fittings

Page 34

Maintenance

Check Tire Pressures

Service Interval: Every 50 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Check tire pressure in drive tires.

3.Inflate drive tires to 13 psi (90 kPa).

4.Semi-pneumatic caster tires Do Not need to be inflated.

Note: Do Not add any type of tire liner or foam fill material to the tires. Excessive loads created by foam filled tires may cause failures to the hydro drive system, frame, and other components. Foam filling tires will void the warranty.

Check Condition Of Belts

Service Interval: Every 50 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Remove left and right belt shields on deck and lift up floor pan to inspect deck drive belt.

3.Check under machine to inspect the pump drive belt.

Note: No adjustments are required for belt tension.

Lubricate Grease Fittings

Note: See chart for service intervals.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lubricate fittings with one to two pumps of NGLI grade #2 multi-purpose gun grease.

Refer to the following chart for fitting locations and lubrication schedule.

Lubrication Chart

Fitting

Initial

Number of

Service

Locations

Pumps

Places

Interval

1. Deck and

1

2

Yearly

Pump Idler

 

 

 

Pivots

 

 

 

2. Front

*0

2

*Yearly

Caster

 

 

 

Pivots

 

 

 

*See step 3 for special lubrication instructions on the front caster pivots.

3.Lubricate front caster pivots once a year. Remove hex plug and cap. Thread grease zerk in hole and pump with grease until it oozes out around top bearing. Remove grease zerk and thread plug back in. Place cap back on.

Lubricate Caster Wheel Hubs

Service Interval: As required

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

 

Figure 24

1. Seal guard

2. Spacer nut with wrench

 

flats

2.Remove caster wheel from caster forks.

3.Remove seal guards from the wheel hub.

4.Remove one of the spacer nuts from the axle assembly in the caster wheel. Note that thread locking adhesive has been applied to lock the spacer nuts to the axle. Remove the axle (with the other spacer nut still assembled to it) from the wheel assembly.

5.Pry out seals, and inspect bearings for wear or damage and replace if necessary.

34

Image 34
Contents Lazer Z Advantage Series Models California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 116-0906 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System Operator ControlsSeat Tires & WheelsOverall Length DimensionsOverall Width Overall HeightTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsHour Meter Ignition SwitchFuel Shut-Off Valve Fuel Gauge PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesDeck Lift Pedal Pre-StartOperating Instructions Transport LockStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Adjusting the Cutting Height Driving ForwardTransporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel HubsCheck Spark Plugs Lubricate Brake Handle PivotLubricate Deck Lift Pivot Change Fuel FilterWheel Hub Slotted Nut Torque Specification Check Engine Coolant Level Kawasaki Liquid-Cooled Only Change Engine Coolant Kawasaki Liquid-Cooled OnlyCopper-Based Anti-seize Check Spark Arrester if equippedThread Locking Adhesives Dielectric GreaseAdjustments Deck LevelingDeck Removal Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load Adjustment Clutch ShimRemoving the Shim Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Guards Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled SchematicsLiquid Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.