Exmark 000 & higher Check Spark Arrester if equipped, Thread Locking Adhesives, Dielectric Grease

Page 38

Maintenance

WARNING

Engine compartment contains open belt drives, fans, and other rotating components that can cause injury. Fingers, hands, loose clothing, or jewelry can get caught by the rotating fan and drive shaft.

•Do Not operate machine without the covers in place.

•Keep fingers, hands, and clothing clear of rotating components.

•Shut off engine, wait for moving parts to stop, engage parking brake and remove key, before performing maintenance.

6.With the cap off the radiator, start the engine as stated in the Operating Instructions Section.

7.Operate engine until the engine thermostat opens and coolant is circulating through the radiator core. As air is purged from the engine block and the coolant level drops, add additional coolant to the radiator.

8.When the radiator is completely full and no additional coolant can be added, continue running and install the radiator cap. Make sure that the cap is completely seated by pressing down firmly while turning until the cap stops. Once the cap is installed, the engine may be stopped.

Check Spark Arrester (if equipped)

Service Interval: Every 50 hours

WARNING

Hot exhaust system components may ignite gasoline vapors even after the engine is stopped. Hot particles exhausted during engine operation may ignite flammable materials. Fire may result in personal injury or property damage.

Do Not refuel or run engine unless spark arrester is installed.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Wait for muffler to cool.

3.If any breaks in the screen or welds are observed, replace arrester.

4.If plugging of the screen is observed, remove arrester and shake loose particles out of the arrester and clean screen with a wire brush (soak in solvent if necessary). Reinstall arrester on exhaust outlet.

Thread Locking Adhesives

Thread locking adhesives such as “Loctite 242” or “Fel-Pro, Pro-Lock Nut Type” are used on the following fasteners:

•ROPS spring pin housing.

•Hydro pump control arm, linkage bolt, and attachment bolt.

•Hydro cooling fan screw.

•Hydro park brake cable anchor mounting bolt

•Sheave and clutch retaining bolt in the end of engine crankshaft.

Thread locking adhesives are required for some hardware on engines — see the Engine manual.

Copper-Based Anti-seize

Copper-based anti-seize is used in the following location:

On threads of Blade Bolts. See Check Mower Blades section.

Dielectric Grease

Dielectric grease is used on all blade type electrical connections to prevent corrosion and loss of contact.

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Lazer Z Advantage Series Models California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 116-0906 Systems SpecificationsModel Numbers Hydrostatic Ground Drive System Operator ControlsSeat Tires & WheelsOverall Length DimensionsOverall Width Overall HeightTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsFuel Shut-Off Valve Ignition SwitchHour Meter Fuel Gauge PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesDeck Lift Pedal Pre-StartOperating Instructions Transport LockEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Adjusting the Cutting Height Driving ForwardTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel HubsCheck Spark Plugs Lubricate Brake Handle PivotLubricate Deck Lift Pivot Change Fuel FilterWheel Hub Slotted Nut Torque Specification Check Engine Coolant Level Kawasaki Liquid-Cooled Only Change Engine Coolant Kawasaki Liquid-Cooled OnlyCopper-Based Anti-seize Check Spark Arrester if equippedThread Locking Adhesives Dielectric GreaseAdjustments Deck LevelingDeck Removal Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Handle Adjustment Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Caster Pivot Bearings Pre-Load Adjustment Clutch ShimRemoving the Shim Clean Hydro Fan Cooling Guards Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled SchematicsLiquid Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents