Exmark 000 & higher manual Clean Engine and Exhaust System Area, Clean Hydro Fan Cooling Guards

Page 47

Maintenance

E.Using a 0.010 inch thick feeler gauge, verify that a gap is present between the rotor and armature face on both sides of the brake pole as shown. (Due to the way the rotor and armature faces wear (peaks and valleys) it is sometimes difficult to measure the true gap.)

Figure 44

1.Feeler gauge

Figure 45

1.Feeler gauge

•If the gap is less than 0.010 inch, then reinstall the shim and reference the Troubleshooting section.

•If the gap is sufficient, proceed to the safety check in step F.

F.Perform the following safety check:

a.Sit on the seat and start the engine.

b.Make sure the blades Do Not engage with the PTO switch “off ” and the clutch disengaged.

If the clutch does not disengage, reinstall the shim and reference the Troubleshooting section.

c.Engage and disengage the PTO switch ten consecutive times to ensure the clutch is functioning properly. If the clutch does not engage properly, reference the Troubleshooting section.

Cleaning

Clean Engine and Exhaust System Area

Service Interval: Before each use or daily (May be required more often in dry or dirty conditions.)

CAUTION

Excessive debris around engine cooling air intake and exhaust system area can cause engine, exhaust area, and hydraulic system to overheat which can create a fire hazard.

Clean all debris from engine and exhaust system area.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Clean all debris from rotating engine air intake screen, around engine shrouding, and exhaust system area.

3.Wipe up any excessive grease or oil around the engine and exhaust system area

Remove Engine Shrouds and Clean Cooling Fins

Service Interval: Every 100 hours

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Remove cooling shroud clean-out covers (Kohler) or cooling shrouds (Kawasaki) from engine and clean cooling fins. Also clean dust, dirt and oil from external surfaces of engine which can cause inadequate cooling.

3.Make sure cooling shroud clean-out covers or cooling shrouds are reinstalled. Operating the engine without cooling shroud clean-out covers or cooling shrouds will cause engine damage due to overheating.

Clean Hydro Fan Cooling Guards

Service Interval: Before each use or daily

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Lazer Z Advantage Series Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 116-0906 Systems SpecificationsModel Numbers Tires & Wheels Operator ControlsSeat Hydrostatic Ground Drive SystemOverall Height DimensionsOverall Width Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationFuel Shut-Off Valve Ignition SwitchHour Meter Drive Wheel Release Valves PTO Engagement SwitchLow Voltage Indicator Fuel GaugeTransport Lock Pre-StartOperating Instructions Deck Lift PedalEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Driving Forward Adjusting the Cutting HeightTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Hydraulic Oil Level Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsWheel Hub Slotted Nut Torque Specification Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyDielectric Grease Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsDeck Removal Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Start the mower while in the operator position Motion Control Linkage Adjustment Electric Clutch AdjustmentMotion Control Handle Adjustment Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Clutch Shim Caster Pivot Bearings Pre-Load AdjustmentRemoving the Shim Clean Hydro Fan Cooling Guards Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Troubleshooting Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledSchematics Electrical Logic Schematic Air-CooledLiquid Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.
Top Page Image Contents