Exmark 000 & higher manual Refer to Check Engine Coolant Level

Page 50

Troubleshooting

Problem

 

Possible Cause

 

Corrective Action

 

 

 

 

 

Engine loses power

1.

Engine load is excessive

1.

Reduce the ground speed.

 

2.

Air cleaner is dirty.

2.

Clean or replace the air cleaner element.

 

3.

Oil level in the crankcase is low.

3.

Add oil to the crankcase.

 

4.

Cooling fins and air passages for the

4.

Remove the obstructions from the cooling

 

 

engine are plugged.

 

fins and air passages.

 

5.

Dirt in fuel filter.

5.

Replace the fuel filter.

 

6.

Dirt, water, or stale fuel is in the fuel

6.

Contact an Authorized Service Dealer.

 

 

system.

 

 

 

 

 

 

 

Engine overheats. (Coolant temperature

1.

Temperature is increasing on coolant

1.

Refer to Check Engine Coolant Level

gauge is approaching the red zone or warning

 

temperature gauge.

 

section in the Maintenance.

buzzer emits beep.)

2.

Coolant level is low.

2.

Refer to Check Engine Coolant Level

 

 

 

 

 

section in the Maintenance.

 

3.

Debris on or around radiator.

3.

Remove debris.

 

4.

Engine load is excessive.

4.

Reduce the ground speed.

 

5.

Oil level in the crankcase is low.

5.

Add oil to the crankcase.

 

6.

Cooling fins and air passages for the

6.

Remove the obstructions from the cooling

 

 

engine are plugged.

 

fins and air passages.

 

 

 

 

 

Mower pulls left or right (with levers fully

1.

Tire pressure in drive tires not correct.

1.

Adjust tire pressure in the drive tires.

forward)

 

 

 

 

 

 

 

 

 

Machine does not drive

1.

Drive release handle not in “operating”

1.

Position handle in “operating” position;

 

 

position.

 

see Drive Wheel Release Valves section

 

 

 

 

in Operation.

 

2.

Drive or pump belt is worn, loose or

2.

Change the belt.

 

 

broken.

 

 

 

3.

Drive or pump belt is off a pulley.

3.

Change the belt.

 

4.

Broken or missing idler spring.

4.

Replace the spring.

 

5.

Hydraulic fluid level is low or too hot.

5.

Add hydraulic fluid to reservoir or let it

 

 

 

 

cool down.

 

 

 

 

 

Uneven cutting height.

1.

Blade(s) not sharp.

1.

Sharpen the blade(s).

 

2.

Cutting blade(s) is/are bent.

2.

Install new cutting blade(s).

 

3.

Mower deck is not level.

3.

Level mower deck from side-to-side and

 

 

 

 

front-to-rear.

 

4.

Underside of mower is dirty.

4.

Clean the underside of the mower.

 

5.

Tire pressure in drive tires not correct.

5.

Adjust tire pressure in the drive tires.

 

6.

Blade spindle bent.

6.

Contact an Authorized Service Dealer.

 

7.

Tips of adjacent blades are at an uneven

7.

Replace blades, spindles and (or) check

 

 

cutting height. Blades tips should be even

 

for damage to mower deck.

 

 

within 3/16 inch which is approximately

 

 

 

 

one blade thickness.

 

 

 

 

 

 

 

Abnormal vibration

1.

Cutting blade(s) is/are bent or unbalanced.

1.

Install new cutting blade(s).

 

2.

Blade mounting bolt is loose.

2.

Tighten the blade mounting bolt.

 

3.

Engine mounting bolts are loose.

3.

Tighten the engine mounting bolts.

 

4.

Loose engine pulley, idler pulley, or blade

4.

Tighten the appropriate pulley.

 

 

pulley.

 

 

 

5.

Engine pulley is damaged.

5.

Contact an Authorized Service Dealer.

 

6.

Blade spindle is bent.

6.

Contact an Authorized Service Dealer.

 

 

 

 

 

50

Image 50
Contents Lazer Z Advantage Series Models California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 116-0906 Systems SpecificationsModel Numbers Hydrostatic Ground Drive System Operator ControlsSeat Tires & WheelsOverall Length DimensionsOverall Width Overall HeightTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsFuel Shut-Off Valve Ignition SwitchHour Meter Fuel Gauge PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesDeck Lift Pedal Pre-StartOperating Instructions Transport LockEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Adjusting the Cutting Height Driving ForwardTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel HubsCheck Spark Plugs Lubricate Brake Handle PivotLubricate Deck Lift Pivot Change Fuel FilterWheel Hub Slotted Nut Torque Specification Check Engine Coolant Level Kawasaki Liquid-Cooled Only Change Engine Coolant Kawasaki Liquid-Cooled OnlyCopper-Based Anti-seize Check Spark Arrester if equippedThread Locking Adhesives Dielectric GreaseAdjustments Deck LevelingDeck Removal Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Handle Adjustment Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Caster Pivot Bearings Pre-Load Adjustment Clutch ShimRemoving the Shim Clean Hydro Fan Cooling Guards Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled SchematicsLiquid Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.