Exmark 000 & higher manual Disengaging the PTO, Stopping the Engine, Driving the Machine

Page 25

Operation

DANGER

An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also, contact with the blade could occur. Thrown objects or blade contact can cause serious injury or death.

Never operate the mower with the discharge deflector raised, removed, or altered unless there is a grass collection system or mulch kit in place and working properly.

The PTO push-pull switch engages the cutting blades. Be sure that all persons are clear of the mower deck and discharge area before engaging PTO.

Important: Operator must be in seat before the PTO can be engaged.

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Pull the PTO switch outward to engage the blades.

3.Place the throttle in the “FAST” position to begin mowing.

Disengaging the PTO

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Push the PTO switch in to disengage the blades.

Stopping the Engine

1.Bring the unit to a full stop.

2.Disengage the PTO.

3.Move the motion control levers out to the neutral lock position.

4.Engage the parking brake.

5.Place the throttle midway between the “SLOW” and “FAST” positions.

6.Allow the engine to run for a minimum of 15 seconds, then turn the ignition switch to the “OFF” position to stop the engine.

7.Remove the key to prevent children or other unauthorized persons from starting engine.

8.Close the fuel shut-off valve, located behind and below the seat, when the machine will not be in

use for a few days, when transporting, or when the unit is parked inside a building.

Driving the Machine

CAUTION

Machine can spin very rapidly by positioning one lever too much ahead of the other. Operator may lose control of the machine, which may cause damage to the machine or injury.

Use caution when making turns.

Slow the machine down before making sharp turns.

Important: To begin movement (forward or backward) the operator must be in the seat, the brake lever must be disengaged (pushed down) before the motion control levers can be moved in or the engine will stop.

When the motion control levers are positioned fully outward (apart) in the T-slot, the drive system is in the neutral lock position (Figure 15).

Note: The “N” LCD indicator appears when both levers are in the neutral lock position.

When the motion control levers are moved directly inward (together) the drive system is in the neutral operate position.

25

Image 25
Contents Lazer Z Advantage Series Models California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 116-0906 Model Numbers SpecificationsSystems Seat Operator ControlsHydrostatic Ground Drive System Tires & WheelsOverall Width DimensionsOverall Length Overall HeightAccessory Weight Table Worksheet Curb WeightTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireTorque Requirements Product OverviewControls OperationHour Meter Ignition SwitchFuel Shut-Off Valve Low Voltage Indicator PTO Engagement SwitchFuel Gauge Drive Wheel Release ValvesOperating Instructions Pre-StartDeck Lift Pedal Transport LockStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Driving Forward Adjusting the Cutting HeightTransporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeCheck Mower Blades Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareCheck Hydraulic Oil Level Change Engine OilCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Lubricate Brake Handle PivotCheck Spark Plugs Change Fuel FilterWheel Hub Slotted Nut Torque Specification Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyThread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Dielectric GreaseDeck Leveling AdjustmentsDeck Removal Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Start the mower while in the operator position Motion Control Linkage Adjustment Electric Clutch AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentMotion Control Handle Adjustment Clutch Shim Caster Pivot Bearings Pre-Load AdjustmentRemoving the Shim Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Guards Clean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Troubleshooting Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledSchematics Electrical Logic Schematic Air-CooledLiquid Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

000 & higher specifications

Exmark has long been synonymous with excellence in the world of lawn care and landscaping, and their 000 & higher, 0,312 series is no exception. Engineered for both professional landscapers and passionate homeowners, this series brings together innovative technology with robust design to deliver unparalleled performance and durability.

One standout feature of this series is its powerful engine options, which ensure efficient cutting and grass handling capabilities. The engines are designed to provide consistent power and reliability, even in tough conditions. This reliability is complemented by high-quality cutting decks that deliver precision cuts and exceptional mulching abilities, ensuring that your lawn stays healthy and vibrant.

The cutting height adjustment system allows users to easily modify the height to suit various types of grass and landscaping needs. This adaptability ensures that your grass is always maintained at the optimal length for health and aesthetics. The ergonomic design of the handles incorporates comfort grips, reducing fatigue during prolonged use while providing excellent control over the machine.

Another significant aspect of the 000 & higher, 0,312 series is its advanced technology integration. Many models in this series come equipped with efficient fuel systems that enhance performance while minimizing fuel consumption. Furthermore, the inclusion of intelligent controls and monitoring systems enables users to make informed adjustments, ensuring that the equipment operates at peak performance.

The robust construction of the chassis and frame means that these machines can withstand the rigors of everyday use in various landscapes. The high-quality materials used in the manufacturing process enhance the longevity of the equipment, making it a worthy investment for those serious about maintaining their lawns.

In addition, Exmark places a strong emphasis on safety features. The series includes protective shields and easy-to-access controls that prioritize user safety without compromising on functionality. Maintenance is made simple through user-friendly designs, allowing for quick access to essential components.

In conclusion, the Exmark 000 & higher, 0,312 series presents a perfect blend of power, innovation, and user-focused features. With its reliable performance, flexible adjustment options, and sturdy design, this series continues to set the standard for excellence in lawn care equipment. Whether you’re a professional or a homeowner, the Exmark 000 & higher, 0,312 series stands ready to meet all your landscaping needs.