Husqvarna 115 13 81-96, 445e EPA III Cutting equipment designed to reduce kickback, Bar, Chain

Page 11

GENERAL SAFETY PRECAUTIONS

•Maintain the correct depth gauge setting! Follow our instructions and use the recommended depth gauge clearance. Too large a clearance increases the risk of kickback.

•Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

•Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

Cutting equipment designed to reduce kickback

WARNING! Faulty cutting equipment or ! the wrong combination of bar and saw

chain increases the risk of kickback! Only use the bar/saw chain combinations we recommend, and follow the filing instructions. See instructions under the heading Technical data.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well- maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the lower the chance of kickback.

Chain

A chain is made up of a number of links, which are available in standard and low-kickback versions.

IMPORTANT! No saw chain design eliminates the danger of kickback.

WARNING! Any contact with a rotating ! saw chain can cause extremely serious

injuries.

Some terms that describe the bar and chain

To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain with a bar and chain combinations recommended by Husqvarna. See instructions under the heading Technical Data for a list of replacement bar and chain combinations we recommend.

Bar

•Length (inches/cm)

•Number of teeth on bar tip sprocket (T).

•Chain pitch (inches). The spacing between the drive links of the chain must match the spacing of the teeth on the bar tip sprocket and drive sprocket.

•Number of drive links. The number of drive links is determined by the length of the bar, the chain pitch and the number of teeth on the bar tip sprocket.

•Bar groove width (inches/mm). The groove in the bar must match the width of the chain drive links.

•Chain oil hole and hole for chain tensioner. The bar must be matched to the chain saw design.

Chain

•Chain pitch (inches)

115 13 81-96 Rev.3 2008-12-16

English – 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents EPA III 445e EPA 450e EPA You will find the following labels on your chain saw KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsChain brake and front hand guard Machine′s safety equipmentAlways use common sense Personal protective equipmentGeneral Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerInjuries Some terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Filling with chain oil Lubricating cutting equipment445e, 450e Which could lead to serious, even fatal injuries Chain oilChecking wear on cutting equipment Checking chain lubricationChain drive sprocket Needle bearing lubricationBar 445e, 450e AssemblyFitting the bar and chain 445Assembly Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageCold engine Starting and StoppingStarting and stopping StartingStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueSafe distance Tree felling techniqueLimbing Log is supported at one end. There is a high riskDirectional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburetor adjustment Immediately Checking the inertia brake releaseMuffler Tensioning the recoil spring StarterReplacing the starter cord Fitting the starter Air filterReplacing the return and drive springs Cooling system Spark plugLubricating the bar tip sprocket Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature -5C 23F or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsEtiquetas que se encuentran en la motosierra Aclaracion DE LOS SimbolosSímbolos en la máquina Símbolos en el manual de instruccionesPrecauciones de seguridad para usuarios de IndiceÍndice Apreciado cliente Introduccion¿Qué es qué en la motosierra? ¿QUE ES QUE?Importante Instrucciones Generales DE SeguridadMedidas a tomar antes de utilizar una motosierra nueva Freno de cadena con protección contra reculadas Emplee siempre el sentido comúnEquipo de protección personal Equipo de seguridad de la máquinaInstrucciones Generales DE Seguridad Protección de la mano derecha Fiador del aceleradorCaptor de cadena Silenciador Equipo de corteSistema amortiguador de vibraciones Botón de paradaCadena Reglas básicasEquipo de corte reductor de reculadas EspadaGeneralidades sobre el afilado de los dientes cortantes Generalidades sobre el ajuste de la profundidad de corte Tensado de la cadena Control de la lubricación de la cadena Lubricación del equipo de corteRepostaje de aceite para cadena de motosierra ¡ATENCION! La mayoría de los Piñón de arrastre de la cadenaLubricación del cojinete de agujas Control del desgaste del equipo de corteDeben utilizarse guantes protectores MontajeMontaje de la espada y la cadena ¡ATENCION! Para manipular la cadenaMontaje Carburante Manipulacion DEL CombustibleAlmacenamiento prolongado RepostajeSeguridad en el uso del combustible Transporte y almacenamientoArranque Arranque Y ParadaArranque y parada Parada Reglas básicas de seguridad Tecnica DE TrabajoAntes de utilizar la máquina Instrucciones generales de trabajoReglas básicas Designaciones Técnica básica de corteDistancia de seguridad Técnica de talaDesramado Corte de indicación Dirección de derriboCorte de ramas bajas y camino de retirada Corte de derribo ¿Qué es la reculada? Medidas preventivas de las reculadasTratamiento de una tala fallida Tronzado del tronco Ajuste del carburador MantenimientoGeneralidades Detenerse inmediatamente Control de la función de inerciaSilenciador Tensado del muelle de retorno Mecanismo de arranqueCambio del cordón de arranque Montaje del mecanismo de arranque Filtro de aireCambio del muelle de retorno y el muelle de arrastre Sistema refrigerante BujíaEngrase del cabezal de rueda de la espada Lubricación del cojinete de agujasTemperaturas de -5C 23F o inferiores Depuración centrífuga Air InjectionUtilización en invierno Programa de mantenimiento 445 445e 450e Datos TecnicosAfilado y calibres de afilado de la cadena de sierra Combinaciones de espada y cadenaSUS Derechos Y Obligaciones DE Garantia Garantia DEL Sistema DE Control DE EmisionesLista DE Componentes DE LA Garantia DE Control DE Emisiones Otras precauciones de seguridad Precauciones DE Seguridad DE LA Norma AmericanaPrecauciones de seguridad para usuarios de motosierras Precauciones de seguridad en reculadas115 13 81-96 Rev.3 ´z+SF3¶6U¨ 115 13 81-96 Rev.3 1151381-95
Top Page Image Contents