Husqvarna Z4818BIA, 968999250 manual Before Removing Mower from the Skid, Attach Seat See Fig

Page 13

ASSEMBLY

BEFORE REMOVING THE

MOWER FROM THE SKID

ATTACH SEAT (See Fig. 1)

The seat position should be adjusted forward or backward so that the operator can comfortably reach the deck lift pedal and safely operate the mower. See "Service and Adjustment" Section of this manual.

•Remove protective wrap from the seat.

•Remove the three prong knobs and washers from the seat and place in the storage area in the right side console.

•Raise the seat pan up so that the bottom can be easily accessed.

•Securing one of the three prong knobs and washers, insert it thru the seat pan slot and into the corresponding threaded hole in the seat bottom.

•Repeat for the other three holes.

•Tighten the three prong knobs in the approximate position desired for the seat.

•Connect the wiring harness to the seat switch.

Adjustments may be required to position the seat in the desired position. Refer to the "Service and Adjustment" section of this manual.

ATTACH CONTROL LEVERS (See Fig. 2)

•Using the 9/16" wrench or socket and ratchet, remove the bottom hex bolt and spring washer from the control arm.

•Rotate the control lever up until the bolt and spring washer can be placed thru the slot in the bottom of the control lever and threaded back into the control arm.

•Center the hex bolt in the slot on the control lever. Using the wrench or ratchet, tighten both the top and bottom hex bolts.

•Repeat on opposite side of the mower.

Adjustments may be required to get uniform positioning of the control lever. Refer to the "Service and Adjustment" section of this manual.

NOTE: You may now roll or drive the mower off of the skid. Follow the appropriate instruction below to remove the mower from the skid.

1

2

3

CZ-1

FIGURE 1

1.SEAT PAN

2.KNOBS

3.WIRE HARNESS

1

2

3

4

CZ-2

FIGURE 2

1.CONTROL LEVER

2.CONTROL ARM

3.HEX BOLTS

4.NEUTRAL SLOT

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents
968999250 / Z4818BIA Operators Manual ModelsGood Service Contents Symbols and Decals Safety Instructions Safety InstructionsGeneral Use Personal protective equipment Do as follows Driving on SlopesChildren 8011-563 Machine. Activate the parking brake, turn off TransportCustomer Responsibilities SpecificationsTools Required For Assembly AssemblyTo Remove the Mower From Crate Unpack CrateAttach Seat See Fig Before Removing Mower from the SkidAttach Control Levers See Fig Assembly Check the Tire Pressure ChecklistControls OperationIZT Integraded Zeroturn TransaxleBYPASS Linkages To SET Parking Brake See Fig HOW to USE Your MowerDeck Blades EngineTo USE Choke Control See Fig To USE Throttle Control See FigTo Move Forward and Backward See Fig CZ-7 To Adjust the Deck Cutting Height See Fig Rollers See Figure To Adjust ANTI-SCALPTo Operate on Hills To Operate MowerTo Transport See Fig Check Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See Fig Mowing Tips Maintenance Schedule Before Each USE General RecommendationsLubrication Chart Operator Presence System TiresBlade Removal See Fig Blade CareTo Sharpen Blade See Fig Belts BatteryLubrication EngineClean AIR INTAKE/COOLING Areas Clean AIR ScreenAIR Filter Engine OIL FilterIN-LINE Fuel Filter See Figs CleaningMower Service and AdjustmentTo Level Deck FRONT-TO-BACKADJUSTMENTSee Fig To Replace Deck Belt To Replace IZT Integraded Zeroturn Transaxle Belt See Fig To Adjust the Seat See FigTo Remove Wheels for Repair To Adjust Control Levers See FigTo Attach Jumper Cables To Start AN Engine with a Weak BatteryReplacing Battery See Fig Tracking Adjustment To Adjust Park BrakeStorage BatteryEngine OIL Fuel SystemCylinders OtherProblem Cause Correction Troubleshooting PointsProblemcausecorrection Wiring Schematic
Top Page Image Contents