Husqvarna R 422Ts AWD manual Transport

Page 11

SAFETY INSTRUCTIONS

•Take care with battery maintenance. Explosive gases form in the battery. Never perform maintenance on the battery while smoking or in the vicinity of open flames or sparks. This can cause the battery to explode and cause serious injuries.

•Make sure all nuts and bolts are tightened correctly and that the equipment is in good condition.

•Do not modify safety equipment. Check regularly to be sure it works properly. The machine must not be driven if protective plates, protective covers, safety switches or other protective devices are not fitted or are defective.

•Observe the risk of injury caused by moving or hot parts if the engine is started with the engine cover open or protective cowlings removed.

•Do not change the setting of governors. If you run too fast, you risk damaging the machine components. See chapter on Technical data for highest permitted engine speed.

•Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas.

•Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.

•Never make adjustments with the engine running.

•The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer.

•The blades are sharp and can cause cuts. Wrap the blades or wear protective gloves when handling them.

•Check regularly that the parking brake works. Adjust and maintain as required.

•Reduce the risk of fire by removing grass, leaves and other debris that may have fastened on the machine. Allow the machine to cool before putting it in storage.

Transport

IMPORTANT INFORMATION

The parking brake is not sufficient to lock the machine during transport. Ensure you secure the machine firmly to the transporting vehicle.

•The machine is heavy and can cause serious crush injuries. Take extra care when loading it onto or off a vehicle or trailer.

•Use an approved trailer to transport the machine.

•To secure the machine on the trailer, two approved tension belts and four wedge shaped wheel blocks should be used.

Engage the parking brake and tie the tension belts around stable parts on the machine, e.g. frame or rear wagon. Secure the machine by tensioning the belts towards the back and the front of the trailer respectively.

Place the wheel blocks in front of and behind the rear wheels.

•Check and observe local road traffic regulations before transporting or driving the machine on roads.

English – 11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 422Ts AWD Contents After the first 8 hours Service journalPre-delivery service Introduction Symbols KEY to SymbolsKEY to Symbols Location of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Mechanical Lifting Lever for Cutting Unit Cutting height adjustment leverCutting unit Lever for hydraulic lift of attachmentsFueling Lights and power outletExercise care and refuel outdoors see safety instructions SeatStart the engine DrivingBefore starting Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Stop the engine Driving the RiderBraking Once a Before Year Interval in hours Starting MaintenanceMaintenance schedule Daily Weekly At least MaintenanceCheck front and rear wheel rotation speed according to Removing of the machine hoods CleaningCan result in reduced braking ability Checking and adjusting the steering wiresAdjusting the parking brake Checking the fuel pump’s air filter Checking and adjusting of throttle wireChecking and adjusting the choke wire Replacement of fuel filterReplacing the spark plug Cleaning the engine and mufflerReplacing the air filter Ignition systemMain fuse Check the safety systemReplacing the light bulbs Checking the engine’s cooling air intake When the engine is running. Mind your fingersChecking the tyre pressure Replacing the front belt AssemblyReplacing the centre belt Trapping your hand Fitting the cutting headChecking the cutting unit’s parallelism Removing the cutting unitReplacing the cutting unit belts Adjusting the parallelism of the cutting unitHands when working with the blades Placing in the service position Service position for the cutting unitReplacing the blades Restoring from service position15mm Hands when working with the blades Checking the bladesLubrication Checking the engine’s oil level Lubricating the belt adjusterDriver seat Throttle and choke cables, lever bearingsReplacing the engine oil Lubricate the hydrostatic cable with linksChanging the oil filter Checking the transmission oil level Troubleshooting scheduleLubricate the parking brake wire Hydraulic oil filter changeEngine does not start Problem CauseEngine seems to have no power Battery does not chargeElectrical system Electrical and Hydraulic SystemsHydraulic System Guard ServiceStorage Winter storageTechnical data Vibration levels see note EC Declaration of Conformity Applies to Europe onlySound levels see note Page Page Original instructions 1156988-26 ´z+X§r¶6¨ ´z+X§r¶6¨

R 422Ts AWD specifications

The Husqvarna R 422Ts AWD is a versatile and robust riding lawn mower designed for homeowners seeking powerful performance and exceptional maneuverability. Engineered for a variety of terrains, this mower is particularly noted for its all-wheel drive (AWD) system, allowing for enhanced traction and stability, especially on slopes and uneven surfaces.

One of the standout features of the R 422Ts is its compact design, making it ideal for tighter spaces and smaller yards without sacrificing performance. This mower is equipped with a powerful 422cc engine, providing sufficient power to tackle dense grass and tough mowing conditions. The hydrostatic transmission ensures smooth and effortless speed control, giving users the ability to adjust their mowing pace according to the conditions.

The R 422Ts boasts a cutting width of 42 inches, allowing for efficient mowing coverage. Its effective cutting system utilizes a high-performance three-blade design, ensuring a clean and even cut with every pass. The mower's deck can be adjusted to several cutting heights, accommodating various grass types and seasonal changes.

Comfort and convenience are at the forefront of the R 422Ts design. The ergonomic seat is adjustable and cushioned, providing a comfortable ride even during extended mowing sessions. The intuitive instrument panel offers easy access to controls, including a choke, throttle, and electric starter, making operation straightforward for all users.

Additionally, the Husqvarna R 422Ts features a unique articulated steering system, which allows the rear wheels to follow the front wheels' path, resulting in tight turn capabilities. This design minimizes turf damage and maximizes efficiency, making it easier to navigate around obstacles.

The R 422Ts is compatible with various Husqvarna accessories, enhancing its versatility. Users can easily attach a mulch kit, bagger, or even a snow thrower, transforming this riding mower into an all-year-round utility vehicle.

In summary, the Husqvarna R 422Ts AWD combines power, precision, and adaptability. Its advanced features, including all-wheel drive, hydrostatic transmission, and ergonomic design, ensure that mowing is not only efficient but also enjoyable. Whether tackling a small yard or navigating complex landscaping, the R 422Ts stands out as an excellent choice for homeowners seeking a reliable mowing solution.
Top Page Image Contents