Husqvarna R 422Ts AWD manual Starting the engine with a weak battery, Connecting the jump leads

Page 16

Driving

6When the engine starts release the ignition key immediately back to neutral position.

IMPORTANT INFORMATION

Do not run the starter for more than about 5 seconds at a time. If the engine does not start, wait about 15 seconds before trying again.

7Push the choke lever gradually forward when the engine has started.

8Let the engine run at moderate speed or half throttle for 3- 5 minutes before subjecting it to heavy load.

9 Set the required engine speed with the throttle control.

WARNING! Never run the engine indoors, in

!enclosed or poorly ventilated areas. The exhaust fumes contain toxic carbon monoxide.

Starting the engine with a weak battery

WARNING! Lead-acid batteries produce

!explosive gases. Avoid sparks, open flames and smoking close to batteries. Always wear protective glasses in the vicinity of batteries.

If the battery is too weak to start the engine, it should be recharged.

When jump leads are used for emergency starting, follow the procedure below:

IMPORTANT INFORMATIONYour Rider is equipped with a 12-volt system with negative earth. The other vehicle must also have a 12-volt system with negative earth. Do not use your Rider battery to start other vehicles.

Connecting the jump leads

!

WARNING! Never connect the negative

terminal of the fully-charged battery to, or in

the vicinity of, the negative terminal of the

 

discharged battery. Hydrogen gas may be

 

present with risk of explosion.

•Connect each end of the red cable to the POSITIVE pole

(+) on each battery, exercise care not to short circuit any of the ends against the chassis.

•Connect one end of the black cable to the NEGATIVE pole (-) on the fully charged battery.

•Connect the other end of the black cable to a good CHASSIS EARTH, away from the fuel tank and the battery.

Remove the cables in the reverse order

•The BLACK cable is removed from the chassis and then the fully charged battery.

•Finally the RED cable from both batteries.

IMPORTANT INFORMATION Never use a boost charger/ start booster.

Use only conventional battery chargers. Always disconnect the charger before starting the engine. So called boost chargers/start boosters must never be used. These will often increase the voltage (instead of the current) to generate the power needed to start the engine. This increase in voltage will damage the electrical system.

16 – English

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 422Ts AWD Contents Pre-delivery service Service journalAfter the first 8 hours Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? Location of the controlsSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Cutting height adjustment lever Cutting unitLever for hydraulic lift of attachments Mechanical Lifting Lever for Cutting UnitLights and power outlet Exercise care and refuel outdoors see safety instructionsSeat FuelingBefore starting DrivingStart the engine Connecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order Braking Driving the RiderStop the engine Maintenance Maintenance scheduleDaily Weekly At least Maintenance Once a Before Year Interval in hours StartingCheck front and rear wheel rotation speed according to Cleaning Removing of the machine hoodsAdjusting the parking brake Checking and adjusting the steering wiresCan result in reduced braking ability Checking and adjusting of throttle wire Checking and adjusting the choke wireReplacement of fuel filter Checking the fuel pump’s air filterCleaning the engine and muffler Replacing the air filterIgnition system Replacing the spark plugReplacing the light bulbs Check the safety systemMain fuse Checking the tyre pressure When the engine is running. Mind your fingersChecking the engine’s cooling air intake Replacing the centre belt AssemblyReplacing the front belt Fitting the cutting head Trapping your handRemoving the cutting unit Checking the cutting unit’s parallelismHands when working with the blades Adjusting the parallelism of the cutting unitReplacing the cutting unit belts Service position for the cutting unit Placing in the service positionRestoring from service position 15mm Hands when working with the bladesChecking the blades Replacing the bladesLubrication Lubricating the belt adjuster Driver seatThrottle and choke cables, lever bearings Checking the engine’s oil levelChanging the oil filter Lubricate the hydrostatic cable with linksReplacing the engine oil Troubleshooting schedule Lubricate the parking brake wireHydraulic oil filter change Checking the transmission oil levelProblem Cause Engine seems to have no powerBattery does not charge Engine does not startElectrical and Hydraulic Systems Electrical systemHydraulic System Service StorageWinter storage GuardTechnical data Sound levels see note EC Declaration of Conformity Applies to Europe onlyVibration levels see note Page Page 1156988-26 ´z+X§r¶6¨ ´z+X§r¶6¨ Original instructions

R 422Ts AWD specifications

The Husqvarna R 422Ts AWD is a versatile and robust riding lawn mower designed for homeowners seeking powerful performance and exceptional maneuverability. Engineered for a variety of terrains, this mower is particularly noted for its all-wheel drive (AWD) system, allowing for enhanced traction and stability, especially on slopes and uneven surfaces.

One of the standout features of the R 422Ts is its compact design, making it ideal for tighter spaces and smaller yards without sacrificing performance. This mower is equipped with a powerful 422cc engine, providing sufficient power to tackle dense grass and tough mowing conditions. The hydrostatic transmission ensures smooth and effortless speed control, giving users the ability to adjust their mowing pace according to the conditions.

The R 422Ts boasts a cutting width of 42 inches, allowing for efficient mowing coverage. Its effective cutting system utilizes a high-performance three-blade design, ensuring a clean and even cut with every pass. The mower's deck can be adjusted to several cutting heights, accommodating various grass types and seasonal changes.

Comfort and convenience are at the forefront of the R 422Ts design. The ergonomic seat is adjustable and cushioned, providing a comfortable ride even during extended mowing sessions. The intuitive instrument panel offers easy access to controls, including a choke, throttle, and electric starter, making operation straightforward for all users.

Additionally, the Husqvarna R 422Ts features a unique articulated steering system, which allows the rear wheels to follow the front wheels' path, resulting in tight turn capabilities. This design minimizes turf damage and maximizes efficiency, making it easier to navigate around obstacles.

The R 422Ts is compatible with various Husqvarna accessories, enhancing its versatility. Users can easily attach a mulch kit, bagger, or even a snow thrower, transforming this riding mower into an all-year-round utility vehicle.

In summary, the Husqvarna R 422Ts AWD combines power, precision, and adaptability. Its advanced features, including all-wheel drive, hydrostatic transmission, and ergonomic design, ensure that mowing is not only efficient but also enjoyable. Whether tackling a small yard or navigating complex landscaping, the R 422Ts stands out as an excellent choice for homeowners seeking a reliable mowing solution.
Top Page Image Contents