Husqvarna R 422Ts AWD manual Lubrication

Page 32

Lubrication

General

Remove the ignition key to prevent unintentional movements during lubrication.

When lubricating with an oilcan, it ought to be filled with engine oil.

When lubricating with grease, unless otherwise stated, grease 503 98 96-01 or another chassis or ball bearing grease offering good corrosion protection shall be used.

If the machine is used daily it should be lubricated twice a week.

Wipe away excess grease after lubrication.

It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys. Should this happen, attempt to clean them with spirits. If the belt continues to slip after cleaning with spirits, it must be replaced.

Petrol or other petroleum products must not be used to clean belts.

Accessories

Lubrication or other maintenance of optional equipment or accessories is not described in this manual. This equipment too, naturally, requires maintenance. See the manuals for the respective accessories for instructions.

Lubricating the cables

Grease both ends of the cables and move the controls to end stop positions when lubricating.

Re-attach the rubber covers on the cables after lubrication.

Cables with sheaths will jam if they are not lubricated regularly. A jammed cable may cause malfunction, such as the parking braking being applied. If a cable binds, remove the cable and hang it vertically. Lubricate it with thin engine oil until the oil begins to escape from the bottom.

A tip: Fill a small plastic bag with oil and tape it so that it seals against the casing and allow the cable to hang vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced.

Cutting unit

Remove the front cover.

Lubricate with oil.

- Joints and bearings

Pedal system in the frame tunnel

Lubricate the pedal system in the frame tunnel.

•Remove the cover of the frame tunnel by loosening the screws (two on the steering servo housing).

•Work the pedals and lubricate the moving parts with oil. Lubricate the cables for the brake and drive pedals with oil.

Chains in the frame tunnel

Remove the frame plate by loosening the two screws.

Lubricate the chains in the frame tunnel with oil or chain lubricant spray. Lubricate the steering cable pulley axle with grease.

Links and joints in the cutting adjustment

Lubricate the links and the joints for the cutting height adjustment stay behind the right front wheel. Lubricate with oil.

32 – English

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 422Ts AWD Contents After the first 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? Location of the controlsSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Cutting height adjustment lever Cutting unitLever for hydraulic lift of attachments Mechanical Lifting Lever for Cutting UnitLights and power outlet Exercise care and refuel outdoors see safety instructionsSeat FuelingStart the engine DrivingBefore starting Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Stop the engine Driving the RiderBraking Maintenance Maintenance scheduleDaily Weekly At least Maintenance Once a Before Year Interval in hours StartingCheck front and rear wheel rotation speed according to Cleaning Removing of the machine hoodsCan result in reduced braking ability Checking and adjusting the steering wiresAdjusting the parking brake Checking and adjusting of throttle wire Checking and adjusting the choke wireReplacement of fuel filter Checking the fuel pump’s air filterCleaning the engine and muffler Replacing the air filterIgnition system Replacing the spark plugMain fuse Check the safety systemReplacing the light bulbs Checking the engine’s cooling air intake When the engine is running. Mind your fingersChecking the tyre pressure Replacing the front belt AssemblyReplacing the centre belt Fitting the cutting head Trapping your handRemoving the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Adjusting the parallelism of the cutting unitHands when working with the blades Service position for the cutting unit Placing in the service positionRestoring from service position 15mm Hands when working with the bladesChecking the blades Replacing the bladesLubrication Lubricating the belt adjuster Driver seatThrottle and choke cables, lever bearings Checking the engine’s oil levelReplacing the engine oil Lubricate the hydrostatic cable with linksChanging the oil filter Troubleshooting schedule Lubricate the parking brake wireHydraulic oil filter change Checking the transmission oil levelProblem Cause Engine seems to have no powerBattery does not charge Engine does not startElectrical and Hydraulic Systems Electrical systemHydraulic System Service StorageWinter storage GuardTechnical data Vibration levels see note EC Declaration of Conformity Applies to Europe onlySound levels see note Page Page 1156988-26 ´z+X§r¶6¨ ´z+X§r¶6¨ Original instructions

R 422Ts AWD specifications

The Husqvarna R 422Ts AWD is a versatile and robust riding lawn mower designed for homeowners seeking powerful performance and exceptional maneuverability. Engineered for a variety of terrains, this mower is particularly noted for its all-wheel drive (AWD) system, allowing for enhanced traction and stability, especially on slopes and uneven surfaces.

One of the standout features of the R 422Ts is its compact design, making it ideal for tighter spaces and smaller yards without sacrificing performance. This mower is equipped with a powerful 422cc engine, providing sufficient power to tackle dense grass and tough mowing conditions. The hydrostatic transmission ensures smooth and effortless speed control, giving users the ability to adjust their mowing pace according to the conditions.

The R 422Ts boasts a cutting width of 42 inches, allowing for efficient mowing coverage. Its effective cutting system utilizes a high-performance three-blade design, ensuring a clean and even cut with every pass. The mower's deck can be adjusted to several cutting heights, accommodating various grass types and seasonal changes.

Comfort and convenience are at the forefront of the R 422Ts design. The ergonomic seat is adjustable and cushioned, providing a comfortable ride even during extended mowing sessions. The intuitive instrument panel offers easy access to controls, including a choke, throttle, and electric starter, making operation straightforward for all users.

Additionally, the Husqvarna R 422Ts features a unique articulated steering system, which allows the rear wheels to follow the front wheels' path, resulting in tight turn capabilities. This design minimizes turf damage and maximizes efficiency, making it easier to navigate around obstacles.

The R 422Ts is compatible with various Husqvarna accessories, enhancing its versatility. Users can easily attach a mulch kit, bagger, or even a snow thrower, transforming this riding mower into an all-year-round utility vehicle.

In summary, the Husqvarna R 422Ts AWD combines power, precision, and adaptability. Its advanced features, including all-wheel drive, hydrostatic transmission, and ergonomic design, ensure that mowing is not only efficient but also enjoyable. Whether tackling a small yard or navigating complex landscaping, the R 422Ts stands out as an excellent choice for homeowners seeking a reliable mowing solution.
Top Page Image Contents