Husqvarna R 422Ts AWD manual Seat, Fueling, Lights and power outlet, Release lever

Page 14

PRESENTATION

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

To adjust move the lever under the front edge of the seat to the left, so that the seat can be moved forward or backwards to the required position.

2

1

The seat springing can be adjusted by moving the rubber stops in their mountings on the underside of the seat. Place both stops in the front, middle or rear.

Fueling

The engine runs on unleaded petrol with a minimum octane rating of 87 (not mixed with oil). We recommend the use of biodegradable alkylate petrol. (max. methanol 5%, max. ethanol 10%, max. MTBE 15%)

Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1“).

WARNING! Petrol is highly inflammable.

!Exercise care and refuel outdoors (see safety instructions).

IMPORTANT!

Do not use the fuel tank as a support area.

Lights and power outlet

2 3

1

The lights are switched on and off using the power switch (1) on the control panel.

A seat heater or mobile phone charger are examples of articles that can be connected to the power socket (2).

The power outlet is switched on and off using power switch (3) on the control panel.

The voltage is 12 V.

The power outlet is fuse protected by its own fuse, which is located below the ignition switch.

Release lever

The release control must be pulled out in order for the machine to be moved when the engine is shutoff.

Should you attempt to drive the machine with the clutch controls pulled out it will not move. The drive on the axle is disengaged when one of the controls is pulled out.

Pull the controls to the end positions, do not use an intermediate position.

R 422 Ts AWD have one control for the front axle and one control for the rear axle.

IMPORTANT! Always drive the machine with both clutch controls pressed in.

•Clutch control, rear axle

-Control drawn out, drive system disengaged.

-Control depressed, drive system engaged.

•Clutch control, front axle

The control is positioned on the inside of the left front wheel.

-Rear control (pulled out), drive system disengaged.

-Front control (pushed in), drive system engaged.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 422Ts AWD Contents After the first 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? Location of the controlsInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Lever for hydraulic lift of attachments Cutting height adjustment leverCutting unit Mechanical Lifting Lever for Cutting UnitSeat Lights and power outletExercise care and refuel outdoors see safety instructions FuelingStart the engine DrivingBefore starting Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Stop the engine Driving the RiderBraking Daily Weekly At least Maintenance MaintenanceMaintenance schedule Once a Before Year Interval in hours StartingCheck front and rear wheel rotation speed according to Cleaning Removing of the machine hoodsCan result in reduced braking ability Checking and adjusting the steering wiresAdjusting the parking brake Replacement of fuel filter Checking and adjusting of throttle wireChecking and adjusting the choke wire Checking the fuel pump’s air filterIgnition system Cleaning the engine and mufflerReplacing the air filter Replacing the spark plugMain fuse Check the safety systemReplacing the light bulbs Checking the engine’s cooling air intake When the engine is running. Mind your fingersChecking the tyre pressure Replacing the front belt AssemblyReplacing the centre belt Fitting the cutting head Trapping your handRemoving the cutting unit Checking the cutting unit’s parallelismReplacing the cutting unit belts Adjusting the parallelism of the cutting unitHands when working with the blades Service position for the cutting unit Placing in the service positionChecking the blades Restoring from service position15mm Hands when working with the blades Replacing the bladesLubrication Throttle and choke cables, lever bearings Lubricating the belt adjusterDriver seat Checking the engine’s oil levelReplacing the engine oil Lubricate the hydrostatic cable with linksChanging the oil filter Hydraulic oil filter change Troubleshooting scheduleLubricate the parking brake wire Checking the transmission oil levelBattery does not charge Problem CauseEngine seems to have no power Engine does not startElectrical and Hydraulic Systems Electrical systemHydraulic System Winter storage ServiceStorage GuardTechnical data Vibration levels see note EC Declaration of Conformity Applies to Europe onlySound levels see note Page Page 1156988-26 ´z+X§r¶6¨ ´z+X§r¶6¨ Original instructions

R 422Ts AWD specifications

The Husqvarna R 422Ts AWD is a versatile and robust riding lawn mower designed for homeowners seeking powerful performance and exceptional maneuverability. Engineered for a variety of terrains, this mower is particularly noted for its all-wheel drive (AWD) system, allowing for enhanced traction and stability, especially on slopes and uneven surfaces.

One of the standout features of the R 422Ts is its compact design, making it ideal for tighter spaces and smaller yards without sacrificing performance. This mower is equipped with a powerful 422cc engine, providing sufficient power to tackle dense grass and tough mowing conditions. The hydrostatic transmission ensures smooth and effortless speed control, giving users the ability to adjust their mowing pace according to the conditions.

The R 422Ts boasts a cutting width of 42 inches, allowing for efficient mowing coverage. Its effective cutting system utilizes a high-performance three-blade design, ensuring a clean and even cut with every pass. The mower's deck can be adjusted to several cutting heights, accommodating various grass types and seasonal changes.

Comfort and convenience are at the forefront of the R 422Ts design. The ergonomic seat is adjustable and cushioned, providing a comfortable ride even during extended mowing sessions. The intuitive instrument panel offers easy access to controls, including a choke, throttle, and electric starter, making operation straightforward for all users.

Additionally, the Husqvarna R 422Ts features a unique articulated steering system, which allows the rear wheels to follow the front wheels' path, resulting in tight turn capabilities. This design minimizes turf damage and maximizes efficiency, making it easier to navigate around obstacles.

The R 422Ts is compatible with various Husqvarna accessories, enhancing its versatility. Users can easily attach a mulch kit, bagger, or even a snow thrower, transforming this riding mower into an all-year-round utility vehicle.

In summary, the Husqvarna R 422Ts AWD combines power, precision, and adaptability. Its advanced features, including all-wheel drive, hydrostatic transmission, and ergonomic design, ensure that mowing is not only efficient but also enjoyable. Whether tackling a small yard or navigating complex landscaping, the R 422Ts stands out as an excellent choice for homeowners seeking a reliable mowing solution.
Top Page Image Contents