Husqvarna R 422Ts AWD manual Driving, Before starting, Start the engine

Page 15

Driving

Before starting

•Read the safety instructions and information concerning the placement of controls and functions before starting.

•Perform daily maintenance before starting as set out in the Maintenance schedule.

WARNING! Do not use the machine on

!ground that slopes more than 10°. Mow slopes upwards and downwards, never across. Avoid sudden changes in direction.

IMPORTANT INFORMATION The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt. Impaired cooling of the engine. Risk of major engine damage.

Clear the lawn from stones and other objects which can be thrown out by the blades.

•Localise and mark stones and other fixed objects to avoid collision.

•Start with a high cutting height and reduce down until the required mowing results are obtained.

•The mowing result will be best with the highest permitted engine speed, see technical data, (the blades rotate rapidly) and low speed (the Mower moves slowly). If the grass is not too high and thick, the driving speed can be increased without noticeably depreciating the mowing result.

•The best lawns are achieved if the grass is cut often. Mowing becomes more uniform and the grass cuttings become more evenly distributed over the surface. The total time consumption is not greater since it is possible to select a higher driving speed without inferior mowing results.

•Avoid mowing a wet lawn. The mowing results are inferior since the wheels sink down into the soft lawn.

•Hose down the cutting unit with water underneath each time it is used, avoid using a high pressure washer. The cutting unit should then be put in the service position.

•When the BioClip function is used, it is very important that the mowing interval is not too long.

Start the engine

1Make sure that the clutch control is depressed. R 422 Ts AWD have one control for the front axle and one control for the rear axle.

2Lift up the cutting unit by pulling the lever backwards to locked position (transport position) and apply the parking brake.

2

1

The engine can not be started if the parking brake is not pressed down.

3 Move the throttle control to the middle position.

4If the engine is cold move the choke lever backwards to its end position.

5 Turn the ignition key to the start position.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 422Ts AWD Contents Service journal Pre-delivery serviceAfter the first 8 hours Introduction Symbols KEY to SymbolsKEY to Symbols Location of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Mechanical Lifting Lever for Cutting Unit Cutting height adjustment leverCutting unit Lever for hydraulic lift of attachmentsFueling Lights and power outletExercise care and refuel outdoors see safety instructions SeatDriving Before startingStart the engine Starting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order Driving the Rider BrakingStop the engine Once a Before Year Interval in hours Starting MaintenanceMaintenance schedule Daily Weekly At least MaintenanceCheck front and rear wheel rotation speed according to Removing of the machine hoods CleaningChecking and adjusting the steering wires Adjusting the parking brakeCan result in reduced braking ability Checking the fuel pump’s air filter Checking and adjusting of throttle wireChecking and adjusting the choke wire Replacement of fuel filterReplacing the spark plug Cleaning the engine and mufflerReplacing the air filter Ignition systemCheck the safety system Replacing the light bulbsMain fuse When the engine is running. Mind your fingers Checking the tyre pressureChecking the engine’s cooling air intake Assembly Replacing the centre beltReplacing the front belt Trapping your hand Fitting the cutting headChecking the cutting unit’s parallelism Removing the cutting unitAdjusting the parallelism of the cutting unit Hands when working with the bladesReplacing the cutting unit belts Placing in the service position Service position for the cutting unitReplacing the blades Restoring from service position15mm Hands when working with the blades Checking the bladesLubrication Checking the engine’s oil level Lubricating the belt adjusterDriver seat Throttle and choke cables, lever bearingsLubricate the hydrostatic cable with links Changing the oil filterReplacing the engine oil Checking the transmission oil level Troubleshooting scheduleLubricate the parking brake wire Hydraulic oil filter changeEngine does not start Problem CauseEngine seems to have no power Battery does not chargeElectrical system Electrical and Hydraulic SystemsHydraulic System Guard ServiceStorage Winter storageTechnical data EC Declaration of Conformity Applies to Europe only Sound levels see noteVibration levels see note Page Page Original instructions 1156988-26 ´z+X§r¶6¨ ´z+X§r¶6¨

R 422Ts AWD specifications

The Husqvarna R 422Ts AWD is a versatile and robust riding lawn mower designed for homeowners seeking powerful performance and exceptional maneuverability. Engineered for a variety of terrains, this mower is particularly noted for its all-wheel drive (AWD) system, allowing for enhanced traction and stability, especially on slopes and uneven surfaces.

One of the standout features of the R 422Ts is its compact design, making it ideal for tighter spaces and smaller yards without sacrificing performance. This mower is equipped with a powerful 422cc engine, providing sufficient power to tackle dense grass and tough mowing conditions. The hydrostatic transmission ensures smooth and effortless speed control, giving users the ability to adjust their mowing pace according to the conditions.

The R 422Ts boasts a cutting width of 42 inches, allowing for efficient mowing coverage. Its effective cutting system utilizes a high-performance three-blade design, ensuring a clean and even cut with every pass. The mower's deck can be adjusted to several cutting heights, accommodating various grass types and seasonal changes.

Comfort and convenience are at the forefront of the R 422Ts design. The ergonomic seat is adjustable and cushioned, providing a comfortable ride even during extended mowing sessions. The intuitive instrument panel offers easy access to controls, including a choke, throttle, and electric starter, making operation straightforward for all users.

Additionally, the Husqvarna R 422Ts features a unique articulated steering system, which allows the rear wheels to follow the front wheels' path, resulting in tight turn capabilities. This design minimizes turf damage and maximizes efficiency, making it easier to navigate around obstacles.

The R 422Ts is compatible with various Husqvarna accessories, enhancing its versatility. Users can easily attach a mulch kit, bagger, or even a snow thrower, transforming this riding mower into an all-year-round utility vehicle.

In summary, the Husqvarna R 422Ts AWD combines power, precision, and adaptability. Its advanced features, including all-wheel drive, hydrostatic transmission, and ergonomic design, ensure that mowing is not only efficient but also enjoyable. Whether tackling a small yard or navigating complex landscaping, the R 422Ts stands out as an excellent choice for homeowners seeking a reliable mowing solution.
Top Page Image Contents