Husqvarna 325RX, 323R, 325RDX manual Cutting equipment, Sharpening grass cutters and grass blades

Page 10

GENERAL SAFETY PRECAUTIONS

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

Reduce the risk of blade thrust.

Obtain maximum cutting performance.

Extend the life of cutting equipment.

IMPORTANT!

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Refer to the instructions for the cutting attachment to check the correct way to load the cord and the correct cord diameter.

Keep the teeth of the blade correctly sharpened! Follow our recommendations. Also refer to the instructions on the blade packaging.

Maintain the correct blade setting! Follow our instructions and use the recommended file gauge.

WARNING! Always stop the engine before

!doing any work on the cutting attachment. This continues to rotate even after the throttle has been released. Ensure that the cutting attachment has stopped completely and disconnect the HT lead from the spark plug before you start to work on it.

WARNING! Using an incorrect cutting

!attachment or an incorrectly sharpened blade increases the risk of blade thrust.

Cutting equipment

Saw blades are intended for cutting fibrous types of wood.

Grass blades and grass cutters are intended for cutting coarse grass.

A trimmer head is intended for trimming grass.

General rules

Only use cutting attachments with the guards we recommend! See the chapter on Technical data.

Keep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents.

Keep the correct setting on the saw blade! Follow our instructions and use the recommended setting tool. An incorrectly set saw blade increases the risk of jamming and blade thrust, and damage to the saw blade.

Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced.

Sharpening grass cutters and grass blades

See the cutting attachment packaging for correct sharpening instructions. Sharpen blades and cutters using a single-cut flat file.

10 – English

1151416-95 Rev. 1 2008-12-23

Image 10
Contents 323R 325RX-series KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what on the clearing saw?General Safety Precautions Personal protective equipmentStop switch Machine′s safety equipmentThrottle lockout Quick release Cutting attachment guardVibration damping system MufflerLocking nut Cutting equipment Cutting equipmentSharpening grass cutters and grass blades Sharpening the saw blade Trimmer headFitting the handlebar 323R AssemblyFitting the handlebar 325Rx, 325RDx Assembling the cutting equipment AssemblyAssembling and dismantling the two-piece shaft 325RDx Fitting a blade guard, grass blade and grass cutterFitting the blade guard and saw blade Fitting a trimmer guard and Superauto II 1 trimmer headFitting other guards and cutting attachments Adjusting the harness and clearing sawStandard harness Fuel Handling Fuel safetyFuel Fueling MixingStarting and stopping Starting and StoppingCheck before starting StartingFor throttle handles with a start throttle lock StoppingGeneral working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Working methodsGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingMaintenance CarburetorAdjusting the start throttle speed Fine adjustment of the idle speed TCorrectly adjusted carburetor High speed jet HCooling system MufflerBevel gear Two-piece shaft 325RDx Cleaning the air filterAir filter Spark plugMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataTechnical data 325RX 325RDX Engine MANUFACTURER′S Warranty Coverage Federal and California Emissions Control Warranty Statement Super Auto Page S35 095-.106 T35, T35x ´z+SIe¶5S¨ Page 1151416-95 ´z+SIe¶5S¨ ´z+SIe¶5S¨