Husqvarna 325RDX, 323R, 325RX manual Sharpening the saw blade, Trimmer head

Page 11

GENERAL SAFETY PRECAUTIONS

Sharpen all edges equally to maintain the balance of the blade.

WARNING! Always discard a blade that is

!bent, twisted, cracked, broken or damaged in any other way. Never attempt to straighten a twisted blade so that it can be reused. Only use original blades of the specified type.

Sharpening the saw blade

See the cutting attachment packaging for correct sharpening instructions.

A correctly sharpened blade is essential for working efficiently and to avoid unnecessary wear to the blade and clearing saw.

Make sure that the blade is well supported when you file it. Use a 5.5 mm round file with a file holder.

The filing angle is 15°. File alternate teeth to the right and those in between to the left. If the blade has been heavily pitted by stones it may be necessary to dress the top edges of the teeth with a flat file, in exceptional cases. If so, this should be done before filing with a round file. The top edges must be filed down by the same amount for all the teeth.

Adjust the blade setting. This should be 1 mm.

Trimmer head

IMPORTANT!

Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration.

Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting attachment. See the chapter on Technical data.

Smaller machines generally require small trimmer heads and vice versa. This is because when clearing using a cord the engine must throw out the cord radially from the trimmer head and overcome the resistance of the grass being cleared.

The length of the cord is also important. A longer cord requires greater engine power than a shorter cord of the same diameter.

Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length.

To increase the life of the cord it can be soaked in water for a couple of days. This will make the line tougher so that it lasts longer.

1151416-95 Rev. 1 2008-12-23

English – 11

Image 11
Contents 323R 325RX-series Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what on the clearing saw? What is WHAT?Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentStop switch Muffler Cutting attachment guardVibration damping system Quick releaseLocking nut Sharpening grass cutters and grass blades Cutting equipmentCutting equipment Trimmer head Sharpening the saw bladeFitting the handlebar 325Rx, 325RDx AssemblyFitting the handlebar 323R Fitting a blade guard, grass blade and grass cutter AssemblyAssembling and dismantling the two-piece shaft 325RDx Assembling the cutting equipmentFitting a trimmer guard and Superauto II 1 trimmer head Fitting the blade guard and saw bladeStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments Fuel Fuel safetyFuel Handling Mixing FuelingStarting Starting and StoppingCheck before starting Starting and stoppingStopping For throttle handles with a start throttle lockABC of clearing Basic safety rulesWorking Techniques General working instructionsWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeTrimming Grass trimming with a trimmer headCarburetor MaintenanceHigh speed jet H Fine adjustment of the idle speed TCorrectly adjusted carburetor Adjusting the start throttle speedBevel gear MufflerCooling system Spark plug Cleaning the air filterAir filter Two-piece shaft 325RDxMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataTechnical data 325RX 325RDX Engine MANUFACTURER′S Warranty Coverage Federal and California Emissions Control Warranty Statement Super Auto Page S35 095-.106 T35, T35x ´z+SIe¶5S¨ Page 1151416-95 ´z+SIe¶5S¨ ´z+SIe¶5S¨