Husqvarna 220 AC, 230 ACX manual Corridor width

Page 53

6. MENU FUNCTIONS

•Corridor width (3-2-3)

The Corridor width setting defines the distances from the mower's path to the boundary wire or the guide wire when following these to/from the charging station. The area beside the wires used by the mower is called the Corridor.

A low corridor width value represents a narrow corridor while a high value represents a wide corridor. With a narrow corridor Automower always runs close to the boundary wire respective guide wire. With a wide corridor Automower varies how it runs, i.e. close to and further from the boundary wire respective guide wire.

Corridor

3012-496

Corridor width is a relative distance and is stated on a scale from 0 to 30. The lower the Corridor width value the closer Automower follows the boundary wire and/or guide wire.

Different corridor widths can be set for the boundary wire, guide 1 and on guide 2. The default setting on Automower is set to a value of 6 for both the boundary wire and guide wires.

The higher the stated Corridor width value, the less risk there is of tracks forming. However, a high corridor value means that Automower may find it difficult to enter passages.

A garden with large open areas should have a wide Corridor, i.e. a high Corridor width value. A garden with passages should have a narrow Corridor, i.e. a low value for the Corridor width.

When the value is set to 0 for the Corridor width, Automower will run along the boundary wire, which means it will run with half the mower inside the loop and half the mower outside. As there are often flower beds, hedges and walls along with the boundary wire Corridor width 0 is not normally recommended. Should you still like to state this value, the boundary wire must lay

40 cm from solid objects instead of the normal

Follow loop out

Follow loop in

Corridor width

Test IN

Test OUT

3-2-3

Boundary corridor

Guide 1 corridor

Guide 2 corridor

35 cm.

IMPORTANT INFORMATION

The distance at which the mower follows the boundary wire varies depending on how the working area appears. You should perform some tests to find the highest possible Corridor width. Use the Test IN (3-2-4)function to try different values.

3012-459

54 - English

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Husqvarna Automower 230 ACX/220 AC OPERATOR’S Manual Table of Contents Table of Contents Introduction Introduction SafetySymbols on Automower Symbols in the Operator’s Manual Use Safety instructionsTransport MaintenancePresentation Numbers in the picture correspond to Automower, what’s what?Mowing technique Function of AutomowerCapacity Working method 3012-388 3012-700 3012-400 Search method 1 Irregular Search methodMovement pattern Search method 3 Follow guide wire Search method 2 Follow boundary wireMore than one Automower in a garden One Automower in several gardensCarry out the installation in the following steps InstallationIdeal position of the charging station Installation of the charging stationPreparations Low voltage cable must not be extended Installation and connecting the charging station Do not tread or walk on the charging station plate Best position for the boundary wire Charging the batteryInstallation of the boundary wire Boundaries for the working area 30cm10 cm Secondary areas Boundaries within the working areaSlopes Passages when mowingPassages when searching for the charging station Laying out the boundary wire 3012-281 Joining the boundary wire Laying the boundary wire in towards the charging stationConnecting the boundary wire 3012-284 3012-264 3012-265 3012-507 Linking Automower to the charging station Checking the installationNeed of a guide wire Installation of the guide wirePlacement and connection of the guide wire Maximum 135º Use Charging a discharged batteryStopping Automower Using the timerStarting Automower Restart Switching off AutomowerRestart within 20 seconds Restart after more than 20 secondsAdjusting the cutting height Control panel Shortcuts Select ProgramsNumbers Main switchMain menu Menu functionsBrowse between menus Number seriesAutomower main menu Commands TimerTimer CommandsWeekend timer Timer overrideDay timer Mon Tue Wed Thu Fri Sat Sun Run all Week timerGarden Exit angles Follow loop out Follow loopProportion first Proportion DirectionDistance Follow loop Corridor width Test OUT TestOpen Garden shapeNormal ComplexCheck loop Drive past wireAdvanced Security SettingsPIN code Time lockStop protection Sounds Settings lockOperation KeypadSound Significance LanguageSet time Time and dateSet date Time formatGarden example Proposed installation and settings3012-543 3012-544 3012-545 Corridor width Guide 1 This example only applies to 230 ACX 3012-687 Battery MaintenanceWinter storage ServiceAfter winter storage AutomowerDo not use running water when cleaning CleaningUnderframe and blade disc ChassisBody Replacing the bladesWheels 3012-260 Fault messages Trouble shootingTrouble Shooting Fault symptom Data Automower 230 ACX Automower 220 AC Technical dataEnvironmental Information EU Declaration of Conformity only applies to Europe EU declaration of conformityEU Declaration of Conformity Auto IndexFollow loop Follow loop out Shortcuts Control panel Menus Working area Boundaries 115 03

220 AC, 230 ACX specifications

The Husqvarna 230 ACX and 220 AC are two exceptional chainsaws designed for both professional arborists and homeowners alike. These models are known for their robustness, lightweight designs, and innovative technologies that enhance performance and ease of use.

The Husqvarna 230 ACX features a powerful 38.2cc engine that delivers an impressive cutting performance while remaining fuel-efficient. Its X-Torq engine technology significantly reduces emissions and fuel consumption, making it both environmentally friendly and cost-effective. The chainsaw is equipped with an adjustable oil pump, allowing users to regulate the oil flow based on cutting conditions, ensuring optimal performance and increased chain life.

On the other hand, the Husqvarna 220 AC is similarly equipped with a 36.3cc engine that also utilizes X-Torq technology. This dual focus on power and efficiency makes both models ideal for a variety of cutting tasks, from felling small trees to pruning branches and clearing brush. The lightweight design of these chainsaws, weighing in at just over 10 pounds, allows for easy handling and maneuverability, which is crucial for precision work.

Another standout characteristic of the Husqvarna 230 ACX and 220 AC is their quick-release air filter. This feature simplifies maintenance by allowing users to easily access the filter for cleaning or replacement, ensuring the engine runs smoothly and efficiently. Additionally, the LowVib technology integrated into these chainsaws reduces vibrations, minimizing fatigue during prolonged use and making them comfortable for extended cutting sessions.

Safety is a paramount focus in the design of these chainsaws. Both models come equipped with a chain brake that activates in case of kickback, providing an essential safety feature for users. The chainsaws also have an inertia-activated chain brake and a protective handguard, further ensuring user safety while operating.

In summary, the Husqvarna 230 ACX and 220 AC chainsaws exemplify an impressive blend of power, efficiency, and user-friendly features. With their advanced engine technology, lightweight design, and safety innovations, these chainsaws are perfect for anyone looking for reliable tools for their cutting needs. Whether you are maintaining your landscape or tackling professional jobs, these models stand out as excellent choices in the chainsaw market.
Top Page Image Contents