SMC Networks EX9-AC020EN-PSRJ manuals
Computer Equipment > Switch
When we buy new device such as SMC Networks EX9-AC020EN-PSRJ we often through away most of the documentation but the warranty.
Very often issues with SMC Networks EX9-AC020EN-PSRJ begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Switch SMC Networks EX9-AC020EN-PSRJ is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Switch on our side using links below.
SMC Networks EX9-AC020EN-PSRJ Instruction Manual
19 pages 2.35 Mb
Reduced wiring system Instruction Manual2 ContentsOPERATOR 3 SAFETY4 Product SummarySAFETY ( continued ) System configuration general 6 7 5 SI Unit Model Indication Methodstatus with PLC. How to assemble / disassemble units. SI Unit body EX250 SEN1Communication protocol 6 8 9Mounting/Installation (continued )Layout of the Input BlockPosition the Input Block on the left side of the SI Unit. Layout of the EX9 series Output Block / Power Block Position of End Plate Installation example Dimensions with solenoid valves unconnected [Unit: mm]1 2 3 4 5 6 7 8 9 10 L114 135 156 177 198 219 240 261 282 303 L = 21 x m + 93 10 11I/O mapping Higher-level bus Basic specifications 7 ()8 12 13Communication wiring Cable connection Pin layout and connection diagram of Ethernet Communication Cable Power supply wiring Cable connection Pin layout and connection diagram of power supply connector cable for (unit :mm) 14 15 9 Display/SettingB. Single power supply Connecting one or two power supplies to SI Unit. Settings for display 10 16 17ONIf the stored IP address of an EX250 is not known, please go to the "DHCP Mode" section. SW1 Display/Setting ( continued )*1 : Remote control (SW1 Dip Switches 1 to 4 off)SMC's EX250 SI Unit will respond to the following Rockwell Automation BOOTP/DHCP Server commands. Enable DHCP Disable BOOTP/DHCP *2 : DHCP Mode (SW1 Dip Switches 1 to 4 on) *3 : Hardware AddressingThe IP address range is 192.168.0.1-192.168.0.14. Default settingsAt the time of factory shipment, the product is in "Remote Control Mode" and set to "Enable DHCP". Switch setting 18 19 11 Input Block Model Indication MethodEX250 IEBlock type Input Block Model indication methodEX250-IE1 EX250-IE2 EX250-IE3 Tie-rod (2 pcs.) Accessory Refer to subsection "Mounting/Installation" (page 7) in this manual. 12 20 21EX250-IE1 (M12 connector, 5 pin, Socket) EX250-IE2 (M12 connector, 5 pin, Socket) Input connector pin layoutEX250-IE1/2/3 EX250-IE3 (M8 connector, 3 pin, Socket)Correlation between input number and Input Block Input wiring 22 23 13 Display/SettingEX9 Series Output Block/Power Block EX250-IE1 EX250-IE2/IE3 EX9 PE1 EX9 OE 1 Model Indication Method14 24 25Tie-rod (2 pcs.) Accessory (for socket)(1 pc.) Tie-rod (2 pcs.) Accessory Waterproof capRefer to subsection "Mounting/Installation" (page 7) in this manual. 15 26 27Specification ( continued ) Output connector pin layoutEX9-OET1, EX9-OEP1 (M12 connector, 5 pin, Socket) Output wiringPin alignment and connection drawing of the Output Cable Correlation between output number and Output Block 16 28 29M12 connector, 5 pin, Reverse keyPin alignment and connection drawing of the Power Supply Cable EX9-PE1 pin layout Power Cable (Power Block) Power Cable Jumper (Power Block to EX250-SEN1) Power supply wiring (Power Block) 30 31 17 DisplayOption 18 Troubleshooting
Also you can find more SMC Networks manuals or manuals for other Computer Equipment.