Manuals
/
Brands
/
Baby
/
Safety Gate
/
GTO
/
Baby
/
Safety Gate
GTO
RB923 rev installation manual
Please, tick the box below to download manual:
Contents
Main
2000 GTO, Inc.
RB923
A
I
FOR THE PROFESSIONAL INSTALLER
WARNING!
S
Converting Metric Units to English Equivalents
Converting English Units to Metric Equivalents
Converting Temperature
Table of Contents
Disconnecting the Operator
To Manually Open and Close the Gate, Follow the Procedure Below:
FOR THE SYSTEM DESIGNER
WARNING: To reduce the risk of injury or death:
FOR THE INSTALLER
WARNINGTo reduce the risk of injury or death:
Page
Secondary Means of Protection Against Entrapment
ENTRAPMENT ALARM (UL 325; 30A.1.1A)
Entrapment Alarm (bottom right of control box)
Consumer/End User
Install Warning Signs
Entrapment Protection
Required Safety Precautions for Swing Gates
Warning Signs
!
WARNING
Moving Gate Can Cause Injury Or Death
!
Conforms to UL 325 STANDARDS
Series
product identification and manual operation label installed on control box cover
!
Technical Specifications
8" Nylon Cable Tie (14)
2" Receiver Mounting Screw (4)
Installation of First (Single) Gate Operator Single Gate Operator Parts List
Parts
Hardware (not to scale)
Control Box and Electrical Components
Single Gate Operator Parts List
WARNING
!
Preparing the Gate
Step 1:
Single Gate Operator Installation
Installing The Post Bracket Assembly
Step 3:
Step 6:
Step 5:
Step 4:
Step 8:
Step 9:
Connecting Operator to Post Bracket Assembly
Step 10:
Installing the Gate Bracket
Step 11:
Step 12:
Step 14:
Installing the Open and Closed Position Stops
Step 13:
Step 15:
Mounting the Control Box
Step 16:
Step 17
Step 19
Step 20:
Step 21:
Powering the System
Gate Capacity Chart
Step 22:
Solar Zones and Gate Activity
Zone 1 Zone 2
Zone 3 Zone 3 Zone 3
Important Information About Low voltage Wire
Step 25:
Step 26:
CONTROL BOARD SETTINGS
DIP Switches
Potentiometers
WARNING!
2. Set the transmitter DIP Switches
Setting the Personal Transmitter Code
1. Remove the Transmitter Cover
Mounting the Receiver
3. Teach the New Code to Control Board Memory
Setting the Closed Position Limit Switch
Step 30: For Pull-to-Open Installations:
For Push-to-Open Installations:
Page
Connecting Additional Safety Devices
Compatible Safety Devices
Safety Edges
NOTE: This is not an exhaustive list of compatible safety devices.
Photoelectric Beams
Connecting Accessories
WHT (white) used with GRN
BLU (blue) used with GRN
ORG (orange) used with GRN
Determining The Mounting Position of The Post Bracket Assembly
Push-to-Open Installation
Step PTO-1:
Step PTO-2:
Step PTO-4:
Step PTO-3:
Step PTO-5:
Step PTO-6:
Maintenance and Troubleshooting Guide
Page
Warranty and Repair Service
Limited Two Year Warranty
Column Installation Information
GTO/PRO 2200 Dual Gate System
Second Unit Parts List
2" Receiver Mounting Screw (4)
8" Nylon Cable Tie (14)
Hardware (not to scale)
Installing The Second Unit
Step D2:
39
Step D3:
SECOND OPERATORFIRST OPERATORPOWER IN ALARM ACCESSORY RCVR
Connecting the Second Operator to the Control Board
LEARN
Power Cable from First Operator Power Cable
from Second Operator
Low Voltage Wire from AC Transformer
Setting the Control Board for Dual Gate Installations
LEARN
DIP Switches
Step D-8:
Step D-9:
STEP D-11
LEARN
LEARN
42
GTO Entry Transmitter (RB741)
Accessories Available Through Your Dealer
GTO Digital Keypad (F300)
GTO Bulldog Pedestrian Gate Lock (FM500)
GTO Automatic Gate Lock (FM144)
GTO Automatic Gate Lock (FM142)
ACCESS-ories
GTO Low Voltage Wire (RB509)
Column Mount Lock Receiver (433IH)
Splice Kit - Above Ground (RB707)
Master Pin Lock (RB975)
ACCESS -ories
40 Amp Hour Battery Kit (FB296)
Installation Check list