Step D-11 | GTO RB923 rev guide

FIRST OPERATOR OPENS FIRST,

SECOND OPERATOR CLOSES FIRST

SEQ1 = OFF SEQ2 = ON

If SEQ1 is set to OFF, and SEQ2 is set to ON, the FIRST OPERATOR will open first, and the SECOND OPERATOR will close first (see illustration).

PULL/PUSH

SNGL/DUAL

SEQ1

SEQ2

OBSTRUCT

SENS.

MIN MAX

LEARN

FIRST OPERATOR OPENS FIRST,

FIRST OPERATOR CLOSES FIRST

SEQ1 = ON SEQ2 = ON

If SEQ1 is set to ON, and SEQ2 is set to ON, The FIRST OPERATOR opens and closes first.

PULL/PUSH

SNGL/DUAL

SEQ1

SEQ2

OBSTRUCT

SENS.

MIN MAX

LEARN

BOTH OPERATORS OPEN SIMULTANEOUSLY SECOND OPERATOR CLOSES FIRST

SEQ1 = OFF SEQ2 = OFF

If both SEQ1 and SEQ2 are set to OFF, the FIRST OPERATOR and SECOND OPERATOR open simultaneously. The SECOND OPERATOR will close first.

PULL/PUSH

SNGL/DUAL

SEQ1

SEQ2

OBSTRUCT

SENS.

MIN MAX

LEARN

STEP D-11

Replace the control box cover. Turn the control box power switch to ON. Set the closed gate positions for the first and second operators by adjusting the limit switch

(review step 30).

Your automatic gate operator system is configured for dual pull-to-open gates.

41

Image 44

GTO RB923 rev installation manual Step D-11

Contents

Series Converting Temperature Table of Contents Important Safety Instructions Disconnecting the Operator Before Installation II. During Installation III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against Entrapment Consumer/End User No ONE should Cross the Path of the Moving Gate Entrapment Protection Required Safety Precautions for Swing GatesInstall Warning Signs Moving Gate Can Cause Injury Or Death Technical Specifications GTO/PRO 2000 Series Swing Gate Operators Parts Hardware not to scale Single Gate Operator Parts List Control Box and Electrical Components Step Preparing the GatePull-to-Open Single Gate gate opens into the property Installing The Post Bracket Assembly Step Connecting Operator to Post Bracket Assembly 1/ nut. Note when tighteningRear mount bolt, leave it loose Enough for the operator to pivot Installing the Gate Bracket Installing the Open and Closed Position Stops Mounting the Control Box Never insert the battery with the terminals to the right Battery Powering the System Gate Length Estimated Maximum Number of Cycles Per Day Splice wires togetherSolar Zones and Gate Activity Make sure the exposed wires do not touch each other Not touch each other Control Board Settings DIP Switches Potentiometers Remove the Transmitter Cover Setting the Personal Transmitter CodeSet the transmitter DIP Switches Run the cable through PVC conduit to protect it from damage Mounting the ReceiverMemory For Push-to-Open Installations Setting the Closed Position Limit SwitchStep For Pull-to-Open Installations Step Connecting Additional Safety Devices Photoelectric Beams Compatible Safety DevicesSafety Edges Connecting Accessories WHT white used with GRN greenBLU blue used with GRN green ORG orange used with GRN green Step PTO-2 Push-to-Open InstallationStep PTO-1 Step PTO-3 Step PTO-4Step PTO-5 Step PTO-6 Maintenance and Troubleshooting Guide MaintenancePage GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA Warranty and Repair ServiceLimited Two Year Warranty Column Installation Information Second Unit Parts List GTO/PRO 2200 Dual Gate System Installing The Second Unit GTO Automatic Gate Lock see Accessory CatalogStep D1 StepD2 Connecting the Second Operator to the Control Board StepD3Step D-4 Step D-5 Setting the Control Board for Dual Gate Installations Step D-7Step D-8 Step D-9 Step D-11 GTO Nema Box FM317 Accessories Available Through Your DealerRB101 ACCESS-ories 433IHRB509 Master Pin Lock RB975 Access -ories Replacement Batteries Installation Check list Installation of this operator conforms to Class