Connecting Operator to Post Bracket Assembly | GTO RB923 rev

Connecting Operator to Post Bracket Assembly

Step 7:

Tap the rear mount onto the back of the operator. Align the 3/8" hole in the rear mount with 3/8" hole in the back of the operator and insert the 3/8" bolt through the holes and secure it with the lock nut.

Rear Mount

		Step 8:
	Post Pivot Brackets	Position rear mount between post pivot
	Post Pivot Brackets	brackets. Place 1/ " washers between
		brackets. Place 1/ " washers between
		2
		rear mount and post pivot brackets.
		Align 1/2" hole in rear mount and
		washers with holes in post pivot
		brackets. Attach the rear mount to post
		pivot brackets using 1/2" x 23/4" bolt
		and 1/ " nut. Note: when tightening
		2
		the rear mount bolt, leave it loose
		enough for the operator to pivot
	Rear Mount	freely.
	Rear Mount
1/2" Washers
Step 9:		Clevis Pin
Attach the gate bracket to the front		Clevis Pin
Attach the gate bracket to the front
mount using the clevis pin and hairpin
clip.	Gate Bracket	Push-Pull Tube
	Gate Bracket	Front Mount

IMPORTANT: Thin walled tube and panel gates MUST be reinforced as shown to prevent damage to gate and operator.

Hairpin Clip

14

Image 17

GTO RB923 rev Connecting Operator to Post Bracket Assembly, 1/ nut. Note when tightening, Rear mount bolt, leave it loose

Contents

Series Converting Temperature Table of Contents Disconnecting the Operator Important Safety Instructions II. During Installation Before Installation III. After Installation Secondary Means of Protection Against Entrapment Entrapment Alarm UL 325 30A.1.1A No ONE should Cross the Path of the Moving Gate Consumer/End User Entrapment Protection Required Safety Precautions for Swing GatesInstall Warning Signs Moving Gate Can Cause Injury Or Death GTO/PRO 2000 Series Swing Gate Operators Technical Specifications Hardware not to scale Parts Control Box and Electrical Components Single Gate Operator Parts List Step Preparing the GatePull-to-Open Single Gate gate opens into the property Installing The Post Bracket Assembly Step 1/ nut. Note when tightening Connecting Operator to Post Bracket AssemblyRear mount bolt, leave it loose Enough for the operator to pivot Installing the Gate Bracket Installing the Open and Closed Position Stops Mounting the Control Box Battery Never insert the battery with the terminals to the right Gate Length Powering the System Estimated Maximum Number of Cycles Per Day Splice wires togetherSolar Zones and Gate Activity Not touch each other Make sure the exposed wires do not touch each other DIP Switches Control Board Settings Potentiometers Remove the Transmitter Cover Setting the Personal Transmitter CodeSet the transmitter DIP Switches Run the cable through PVC conduit to protect it from damage Mounting the ReceiverMemory For Push-to-Open Installations Setting the Closed Position Limit SwitchStep For Pull-to-Open Installations Step Connecting Additional Safety Devices Photoelectric Beams Compatible Safety DevicesSafety Edges WHT white used with GRN green Connecting AccessoriesBLU blue used with GRN green ORG orange used with GRN green Step PTO-2 Push-to-Open InstallationStep PTO-1 Step PTO-4 Step PTO-3Step PTO-5 Step PTO-6 Maintenance Maintenance and Troubleshooting GuidePage GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA Warranty and Repair ServiceLimited Two Year Warranty Column Installation Information GTO/PRO 2200 Dual Gate System Second Unit Parts List GTO Automatic Gate Lock see Accessory Catalog Installing The Second UnitStep D1 StepD2 StepD3 Connecting the Second Operator to the Control BoardStep D-4 Step D-5 Step D-7 Setting the Control Board for Dual Gate InstallationsStep D-8 Step D-9 Step D-11 GTO Nema Box FM317 Accessories Available Through Your DealerRB101 433IH ACCESS-oriesRB509 Master Pin Lock RB975 Replacement Batteries Access -ories Installation of this operator conforms to Class Installation Check list