GTO/PRO 2200 Dual Gate System | GTO RB923 rev manual

GTO/PRO 2200 Dual Gate System

Second Unit Parts List

8" Nylon Cable Tie (14)

Parts
	Gate Operator with 50’ Power Cable
Gate Bracket	Post Bracket	Rear Mount
Gate Bracket	Post Pivot Brackets (2)
Closed Position Stop Plate

Hardware (not to scale)

1/2" x 10" Carriage Bolt (2)

1/2" x 33/4" Bolt (2)		11/4"dia x 1/2" Nylon Spacer (2)
1/2" x 23/4" Bolt (3)		1/2"dia x 17/16" Metal Spacer (1)
	(4)	1/2"dia x 17/16" Metal Spacer (1)
	(4)
3/8" x 11/2" Bolt (1)	Screw	1/2" Washer (6)
3/8" x 11/2" Bolt (1)
	Mounting
1/2" x 11/4" Clevis Pin (1)	Mounting	1/2" Lock Nut (7)
1/2" x 11/4" Clevis Pin (1)
Hairpin Clip (1)	Receiver	3/8" Lock Nut (1)
Hairpin Clip (1)
	2"

37

Image 40

GTO RB923 rev installation manual GTO/PRO 2200 Dual Gate System, Second Unit Parts List

Contents

Series Converting Temperature Table of Contents Important Safety Instructions Disconnecting the Operator Before Installation II. During Installation III. After Installation Entrapment Alarm UL 325 30A.1.1A Secondary Means of Protection Against Entrapment Consumer/End User No ONE should Cross the Path of the Moving Gate Install Warning Signs Required Safety Precautions for Swing GatesEntrapment Protection Moving Gate Can Cause Injury Or Death Technical Specifications GTO/PRO 2000 Series Swing Gate Operators Parts Hardware not to scale Single Gate Operator Parts List Control Box and Electrical Components Pull-to-Open Single Gate gate opens into the property Preparing the GateStep Installing The Post Bracket Assembly Step Connecting Operator to Post Bracket Assembly 1/ nut. Note when tighteningRear mount bolt, leave it loose Enough for the operator to pivot Installing the Gate Bracket Installing the Open and Closed Position Stops Mounting the Control Box Never insert the battery with the terminals to the right Battery Powering the System Gate Length Solar Zones and Gate Activity Splice wires togetherEstimated Maximum Number of Cycles Per Day Make sure the exposed wires do not touch each other Not touch each other Control Board Settings DIP Switches Potentiometers Set the transmitter DIP Switches Setting the Personal Transmitter CodeRemove the Transmitter Cover Memory Mounting the ReceiverRun the cable through PVC conduit to protect it from damage Step For Pull-to-Open Installations Setting the Closed Position Limit SwitchFor Push-to-Open Installations Step Connecting Additional Safety Devices Safety Edges Compatible Safety DevicesPhotoelectric Beams Connecting Accessories WHT white used with GRN greenBLU blue used with GRN green ORG orange used with GRN green Step PTO-1 Push-to-Open InstallationStep PTO-2 Step PTO-3 Step PTO-4Step PTO-5 Step PTO-6 Maintenance and Troubleshooting Guide MaintenancePage Limited Two Year Warranty Warranty and Repair ServiceGTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA Column Installation Information Second Unit Parts List GTO/PRO 2200 Dual Gate System Installing The Second Unit GTO Automatic Gate Lock see Accessory CatalogStep D1 StepD2 Connecting the Second Operator to the Control Board StepD3Step D-4 Step D-5 Setting the Control Board for Dual Gate Installations Step D-7Step D-8 Step D-9 Step D-11 RB101 Accessories Available Through Your DealerGTO Nema Box FM317 ACCESS-ories 433IHRB509 Master Pin Lock RB975 Access -ories Replacement Batteries Installation Check list Installation of this operator conforms to Class