GTO RB923 rev installation manual

©2000 GTO, Inc.

RB923 rev - 08/01/01

AUTOMATIC GATE OPERATOR

FOR VEHICULAR SWING GATES

3121 Hartsfield Road • Tallahassee, Florida, USA 32303 Telephone (850) 575-0176 • FAX (850) 575-8912 • www.gtoinc.com

INSTALLATION MANUAL

FOR THE PROFESSIONAL INSTALLER

WARNING!

READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to installand use this automatic gate operator. This gate operator produces a high level of force. Stay clearof the unit while it is operating and exercise caution at all times.This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety,as established and made effective March 1, 2000, by Underwriters Laboratories Inc.

SERIES

Receiver

Run 1000' (max.) of low

voltage wire to control

box from transformer.

(wire not included)

120 Volt Indoor

Transformer

(surge protector

not supplied)

PVC conduit (not included) to protect wire from lawn mowers and weed eaters.

Control Box with Battery

Power Cable Closed Position Positive Stop Plate

Gate Bracket

Post Bracket Assembly

GTO/PRO 2000

Warning Sign

Contents

Main 2000 GTO, Inc. RB923 A I FOR THE PROFESSIONAL INSTALLER WARNING! S Converting Metric Units to English Equivalents Converting English Units to Metric Equivalents Converting Temperature Table of Contents Disconnecting the Operator To Manually Open and Close the Gate, Follow the Procedure Below: FOR THE SYSTEM DESIGNER WARNING: To reduce the risk of injury or death: FOR THE INSTALLER WARNINGTo reduce the risk of injury or death: Page Secondary Means of Protection Against Entrapment ENTRAPMENT ALARM (UL 325; 30A.1.1A) Entrapment Alarm (bottom right of control box) Consumer/End User Install Warning Signs Entrapment Protection Required Safety Precautions for Swing Gates Warning Signs ! WARNING Moving Gate Can Cause Injury Or Death ! Conforms to UL 325 STANDARDS Series product identification and manual operation label installed on control box cover ! Technical Specifications 8" Nylon Cable Tie (14) 2" Receiver Mounting Screw (4) Installation of First (Single) Gate Operator Single Gate Operator Parts List Parts Hardware (not to scale) Control Box and Electrical Components Single Gate Operator Parts List WARNING ! Preparing the Gate Step 1: Single Gate Operator Installation Installing The Post Bracket Assembly Step 3: Step 6: Step 5: Step 4: Step 8: Step 9: Connecting Operator to Post Bracket Assembly Step 10: Installing the Gate Bracket Step 11: Step 12: Step 14: Installing the Open and Closed Position Stops Step 13: Step 15: Mounting the Control Box Step 16: Step 17 Step 19 Step 20: Step 21: Powering the System Gate Capacity Chart Step 22: Solar Zones and Gate Activity Zone 1 Zone 2 Zone 3 Zone 3 Zone 3 Important Information About Low voltage Wire Step 25: Step 26: CONTROL BOARD SETTINGS DIP Switches Potentiometers WARNING! 2. Set the transmitter DIP Switches Setting the Personal Transmitter Code 1. Remove the Transmitter Cover Mounting the Receiver 3. Teach the New Code to Control Board Memory Setting the Closed Position Limit Switch Step 30: For Pull-to-Open Installations: For Push-to-Open Installations: Page Connecting Additional Safety Devices Compatible Safety Devices Safety Edges NOTE: This is not an exhaustive list of compatible safety devices. Photoelectric Beams Connecting Accessories WHT (white) used with GRN BLU (blue) used with GRN ORG (orange) used with GRN Determining The Mounting Position of The Post Bracket Assembly Push-to-Open Installation Step PTO-1: Step PTO-2: Step PTO-4: Step PTO-3: Step PTO-5: Step PTO-6: Maintenance and Troubleshooting Guide Page Warranty and Repair Service Limited Two Year Warranty Column Installation Information GTO/PRO 2200 Dual Gate System Second Unit Parts List 2" Receiver Mounting Screw (4) 8" Nylon Cable Tie (14) Hardware (not to scale) Installing The Second Unit Step D2: 39 Step D3: SECOND OPERATORFIRST OPERATORPOWER IN ALARM ACCESSORY RCVR Connecting the Second Operator to the Control Board LEARN Power Cable from First Operator Power Cable from Second Operator Low Voltage Wire from AC Transformer Setting the Control Board for Dual Gate Installations LEARN DIP Switches Step D-8: Step D-9: STEP D-11 LEARN LEARN 42 GTO Entry Transmitter (RB741) Accessories Available Through Your Dealer GTO Digital Keypad (F300) GTO Bulldog Pedestrian Gate Lock (FM500) GTO Automatic Gate Lock (FM144) GTO Automatic Gate Lock (FM142) ACCESS-ories GTO Low Voltage Wire (RB509) Column Mount Lock Receiver (433IH) Splice Kit - Above Ground (RB707) Master Pin Lock (RB975) ACCESS -ories 40 Amp Hour Battery Kit (FB296) Installation Check list