Invacare Excelerator, Excelerator XLT, Excelerator XLT 2000, Li'l Execelerator manual

Contents

Main Page TABLE OF CONTENTS TABLE OF CONTENTS SPECIFICATIONS SPECIFICATIONS GENERAL GUIDELINES PROCEDURE 1 Operating Information Safety/Handling of Excelerator SAFETY/HANDLING OF EXCELERATOR GENERAL GUIDELINESPROCEDURE 1 GENERAL GUIDELINES PROCEDURE 1 SAFETY INSPECTION/TROUBLESHOOTING/MAINTENANCE PROCEDURE 2 Safety Inspection Checklist Troubleshooting Maintenance SAFETY INSPECTION CHECKLIST TROUBLESHOOTING MAINTENANCE PROCEDURE 2 SAFETY INSPECTION/TROUBLESHOOTING/MAINTENANCE EXCELERATOR ASSEMBLY PROCEDURES (FIGURE 1) NOTE: Invacare recommends that the following proce- dures be performed by a qualified technician. PROCEDURE 11 PROCEDURE 4 PROCEDURE 9 PROCEDURE 6 ASSEMBLY PROCEDURES PROCEDURE 3 ASSEMBLY PROCEDURES W PROCEDURE 4 REAR WHEELS INSTALLING/ADJUSTING THE REAR WHEEL AND QUICK- RELEASE AXLES (FIGURE 1) TIRE/TUBE REPLACEMENT AND TUNING/REPLACEMENT OF SPOKES TIRE PRESSURE DETERMINING/ADJUSTING TOE IN/TOE OUT (FIGURE 3) INSTALLING THE REAR WHEELS WITH THREADED AXLES - EXCELERATOR XLT/XLT 2000 REPLACING CAMBER INSERTS (FIGURE 4) W PROCEDURE 4REAR WHEELS EXCELERATOR FORK ASSEMBLY EXCELERATOR TENSION SPRING EXCELERATOR HAND CRANK ASSEMBLY INSTALLATION PROCEDURE 5 FORK/SPRING/CRANK FORK/CRANK ASSEMBLY REPLACEMENT (FIGURE 3) FORK/SPRING/CRANK PROCEDURE 5 FORK/SPRING/CRANKPROCEDURE 5 NOTE: Make sure the sprocket on the crank handles is in line with the sprocket on the front wheel. NOTE: Laying the chain flat will prevent kinks in the chain. EXCELERATOR XLT/XLT 2000 TENSION SPRING OR ROAD CROWN COMPENSATOR REPLACEMENT/ADJUSTMENT FORK/SPRING/CRANK PROCEDURE 5 LI'L EXCELERATOR - THREE (3) SPEED SHIFTER CABLE LI'L EXCELERATOR - THREE (3) SPEED SHIFTER CABLE ADJUSTMENT EXCELERATOR/EXCELERATOR XLT - SEVEN (7) SPEED SHIFTER CABLE INSTALLATION (FIGURE 4) CHAINPROCEDURE 7 EXCELERATOR/LI'L EXCELERATOR CHAIN ADJUSTMENT EXCELERATOR CHAIN STAY ADJUSTMENT (FIGURE 2) EXCELERATOR/ LI'L EXCELERATOR /CHAIN INSTALLATION W/SEVEN (7) SPEED HUB (FIGURE 1) EXCELERATOR XLT/XLT 2000 CHAIN ADJUSTMENT (FIGURE 3) CHAIN INSTALLATION - TWENTY- FOUR (24) OR TWENTY-SEVEN (27) SPEED CASSETTE (FIGURE 4) USING PARKING BRAKE (FIGURE 1) PARKING BRAKE ADJUSTMENT/ REPLACEMENT (FIGURE 1) BACK HEIGHT ADJUSTMENT (ADJUSTABLE BACKS ONLY) BACK/SEAT PROCEDURE 9 SLIDING SEAT ADJUSTMENT (FIGURES 2 AND 3) B K / BACK ANGLE ADJUSTMENT (FIGURE 4) U Y SEAT UPHOLSTERY REPLACEMENT PROCEDURE 10UPHOLSTERY BACK UPHOLSTERY REPLACEMENT EXCELERATOR/LI'L EXCELERATOR FOOTREST ADJUSTMENT/ REPLACEMENT (FIGURE 1) FOOTRESTPROCEDURE 11 FOOTREST AND LEG GUARD REPLACEMENT (FIGURE 2) PROCEDURE 11 FOOTREST EXCELERATOR XLT/XLT 2000 - USING/REPLACING FOOTREST STRAP OPERATION PROCEDURE 12 HAND CRANK ASSEMBLY SHIFTING GEARS BACKING-UP OPERATIONPROCEDURE 12 BRAKING PARKING BRAKE STEERING/CORNERING MOUNTAIN DRIVE OPTION - SEVEN (7) SPEED SHIFTER ONLY Page PROCEDURE 13OPTIONS COMPUTER INSTALLATION NOTE: Slot in sensor MUST align with metal plug for mile- age etc. to be registered on the computer. SEAT POSITIONING STRAP HORIZONTAL HANDLES (FIGURE 1) TRI-PIN QUAD HANDLES (FIGURE 1) SAFETY HELMET (FIGURE 1) LATERAL SUPPORT (FIGURE 1) LIMITED WARRANTY