Manuals / Brands / Personal Care / Wheelchair / Invacare / Personal Care / Wheelchair

Invacare Excelerator, Excelerator XLT, Excelerator XLT 2000, Li'l Execelerator ASSEMBLY PROCEDURES

1 36

Download 36 pages, 758.53 Kb

11

1. Secure and adjust rear wheels (PROCEDURE 4).

2. Adjust hand crank assembly (PROCEDURE 5).

3. Adjust chain (PROCEDURE 7).

4. Adjust the optional cantilever brake cable (PROCE-

DURE 8).

5. Adjust parking brake (PROCEDURE 8).

6. Adjust back height and/or angle (PROCEDURE 9).

7. Adjust seat position/upholstery (PROCEDURE 10).

8. Adjust footrest (PROCEDURE 11).

9. Check that all hardware is tight.

FIGURE 2 - EXCELERATOR XLT/XLT 2000 ASSEMBLY PROCEDURES

EXCELERATOR XLT/XLT 2000

ASSEMBLY PROCEDURES

(FIGURE 2)

NOTE: Invacare recommends that the following pro-

cedures be performed by a qualified technician.

Tools required:

Adjustable Wrench (10-12-inches)

5, 8 and 32 mm Wrench

3/16-inch Allen Wrench

1/4-inch Allen Wrench

1/2-inch Box Wrench

1/2-inch Socket Wrench

Two (2) Medium Screwdrivers (Flathead and Phillips)

PROCEDURE 3

ASSEMBLY PROCEDURES

A

S

S

E

M

B

L

Y

P

R

O

C

E

D

U

R

E

S

PROCEDURE 4

PROCEDURE 9

PROCEDURE 7

PROCEDURE 11

PROCEDURE 10

PROCEDURE 8

PROCEDURE 5

PROCEDURE 4

PROCEDURE 9 PROCEDURE 7

PROCEDURE 11

PROCEDURE 10

PROCEDURE 8

PROCEDURE 5

EXCELERATOR XLT

EXCELERATOR XLT 2000

Contents

Main Page TABLE OF CONTENTS TABLE OF CONTENTS SPECIFICATIONS SPECIFICATIONS GENERAL GUIDELINES PROCEDURE 1 Operating Information Safety/Handling of Excelerator SAFETY/HANDLING OF EXCELERATOR GENERAL GUIDELINESPROCEDURE 1 GENERAL GUIDELINES PROCEDURE 1 SAFETY INSPECTION/TROUBLESHOOTING/MAINTENANCE PROCEDURE 2 Safety Inspection Checklist Troubleshooting Maintenance SAFETY INSPECTION CHECKLIST TROUBLESHOOTING MAINTENANCE PROCEDURE 2 SAFETY INSPECTION/TROUBLESHOOTING/MAINTENANCE EXCELERATOR ASSEMBLY PROCEDURES (FIGURE 1) NOTE: Invacare recommends that the following proce- dures be performed by a qualified technician. PROCEDURE 11 PROCEDURE 4 PROCEDURE 9 PROCEDURE 6 ASSEMBLY PROCEDURES PROCEDURE 3 ASSEMBLY PROCEDURES W PROCEDURE 4 REAR WHEELS INSTALLING/ADJUSTING THE REAR WHEEL AND QUICK- RELEASE AXLES (FIGURE 1) TIRE/TUBE REPLACEMENT AND TUNING/REPLACEMENT OF SPOKES TIRE PRESSURE DETERMINING/ADJUSTING TOE IN/TOE OUT (FIGURE 3) INSTALLING THE REAR WHEELS WITH THREADED AXLES - EXCELERATOR XLT/XLT 2000 REPLACING CAMBER INSERTS (FIGURE 4) W PROCEDURE 4REAR WHEELS EXCELERATOR FORK ASSEMBLY EXCELERATOR TENSION SPRING EXCELERATOR HAND CRANK ASSEMBLY INSTALLATION PROCEDURE 5 FORK/SPRING/CRANK FORK/CRANK ASSEMBLY REPLACEMENT (FIGURE 3) FORK/SPRING/CRANK PROCEDURE 5 FORK/SPRING/CRANKPROCEDURE 5 NOTE: Make sure the sprocket on the crank handles is in line with the sprocket on the front wheel. NOTE: Laying the chain flat will prevent kinks in the chain. EXCELERATOR XLT/XLT 2000 TENSION SPRING OR ROAD CROWN COMPENSATOR REPLACEMENT/ADJUSTMENT FORK/SPRING/CRANK PROCEDURE 5 LI'L EXCELERATOR - THREE (3) SPEED SHIFTER CABLE LI'L EXCELERATOR - THREE (3) SPEED SHIFTER CABLE ADJUSTMENT EXCELERATOR/EXCELERATOR XLT - SEVEN (7) SPEED SHIFTER CABLE INSTALLATION (FIGURE 4) CHAINPROCEDURE 7 EXCELERATOR/LI'L EXCELERATOR CHAIN ADJUSTMENT EXCELERATOR CHAIN STAY ADJUSTMENT (FIGURE 2) EXCELERATOR/ LI'L EXCELERATOR /CHAIN INSTALLATION W/SEVEN (7) SPEED HUB (FIGURE 1) EXCELERATOR XLT/XLT 2000 CHAIN ADJUSTMENT (FIGURE 3) CHAIN INSTALLATION - TWENTY- FOUR (24) OR TWENTY-SEVEN (27) SPEED CASSETTE (FIGURE 4) USING PARKING BRAKE (FIGURE 1) PARKING BRAKE ADJUSTMENT/ REPLACEMENT (FIGURE 1) BACK HEIGHT ADJUSTMENT (ADJUSTABLE BACKS ONLY) BACK/SEAT PROCEDURE 9 SLIDING SEAT ADJUSTMENT (FIGURES 2 AND 3) B K / BACK ANGLE ADJUSTMENT (FIGURE 4) U Y SEAT UPHOLSTERY REPLACEMENT PROCEDURE 10UPHOLSTERY BACK UPHOLSTERY REPLACEMENT EXCELERATOR/LI'L EXCELERATOR FOOTREST ADJUSTMENT/ REPLACEMENT (FIGURE 1) FOOTRESTPROCEDURE 11 FOOTREST AND LEG GUARD REPLACEMENT (FIGURE 2) PROCEDURE 11 FOOTREST EXCELERATOR XLT/XLT 2000 - USING/REPLACING FOOTREST STRAP OPERATION PROCEDURE 12 HAND CRANK ASSEMBLY SHIFTING GEARS BACKING-UP OPERATIONPROCEDURE 12 BRAKING PARKING BRAKE STEERING/CORNERING MOUNTAIN DRIVE OPTION - SEVEN (7) SPEED SHIFTER ONLY Page PROCEDURE 13OPTIONS COMPUTER INSTALLATION NOTE: Slot in sensor MUST align with metal plug for mile- age etc. to be registered on the computer. SEAT POSITIONING STRAP HORIZONTAL HANDLES (FIGURE 1) TRI-PIN QUAD HANDLES (FIGURE 1) SAFETY HELMET (FIGURE 1) LATERAL SUPPORT (FIGURE 1) LIMITED WARRANTY