Abit KV8 PRO specification

Hardware Setup	2-9

(5). Front Panel Switches & Indicators Headers

This header is used for connecting switches and LED indicators on the chassis front panel.

Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below stands for positive polarity for the LED connection. Please pay attention to connect these headers. A wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could cause system malfunction.

•HLED (Pin 1, 3):

Connects to the HDD LED cable of chassis front panel.

•RST (Pin 5, 7):

Connects to the Reset Switch cable of chassis front panel.

•SPK (Pin 15, 17, 19, 21):

Connects to the System Speaker cable of chassis.

•SLED (Pin 2, 4):

Connects to the Suspend LED cable (if there is one) of chassis front panel.

•PWR-ON (Pin 6, 8):

Connects to the Power Switch cable of chassis front panel.

•PLED (Pin 16, 18, 20):

Connects to the Power LED cable of chassis front panel.

User’s Manual

Page 17

Image 17

Contents

KV8 Pro KV8 Pro Copyright and Warranty Notice Table Of Contents Install Audio Driver Save & Exit Setup Exit Without SavingInstall LAN Driver Install VIA USB 2.0 Driver Introduction Features & SpecificationsIntroduction On board VT6122 10/100/1000 Mb PCI Ethernet Controller 2x USB headers 1x CD-IN, 1x AUX-IN header Back Panel I/O Layout Diagram KV8 Pro Hardware Setup Hardware SetupInstall The Motherboard Install CPU and Heatsink 128MB ~ 1GB Install System MemoryBank 2, 3 DIMM2 Total System Memory 128MB ~ 2GB User’s Manual Chapter Connectors, Headers and Switches FAN Connectors Page USBPWR1 Page VCC Pdif Out Internal Audio Connectors Page Chapter Hardware Setup IDE Connectors Post Code Display Page Chapter Hardware Setup System Management Bus Headers AUDIO1 Bios Setup Bios Setup Chapter User Define ΜGuru Utility Chapter Temperature Monitoring Back to µGuru Utility Setup Menu Voltage Monitoring Beep Temp This item selects the warning temperature limit Fan Speed Monitoring FanEQ Control Standard Cmos Features Back to Standard Cmos Features Setup Menu Page Hard Disk Boot Priority Advanced Bios FeaturesPage Advanced Chipset Features Back to Advanced Chipset Features Setup Menu Dram Timing Selectable Bios Setup OnChip IDE Device Click Enter key to enter its submenu Integrated Peripherals Back to Integrated Peripherals Setup Menu Back to Integrated Peripherals Setup Menu Power Management Setup Resume by Ring Page Resources Controlled By PnP/PCI ConfigurationsBack to PnP/PCI Configurations Setup Menu PCI-1 PCI-2 PCI-3 PCI-4 PCI-5 PCI slot 1 shares IRQ signals with AGP slot Load Optimized Defaults Load Fail-Safe DefaultsSet Password Save & Exit Setup Following screen appears Click Next Click Yes User’s Manual Appendix A. Install VIA 4-in-1 DriverInstall VIA 4-in-1 Driver Appendix a Appendix B. Install Audio Driver Appendix B Appendix C. Install LAN Driver Appendix C Appendix D. Install VIA USB 2.0 Driver Click Yes Click OK Click Print to File KV8 Pro Click Next User’s Manual Appendix E. Install VIA Serial ATA RAID DriverInstall VIA Serial ATA RAID Driver Appendix E Install Abit µGuru Driver Appendix F. Install Abit µGuru Driver Appendix F Award Post Code Definition Appendix G. Post Code Definition Initialize the Apic for P6 class CPU InsteadScreen logo Initialize InitOnboardSuperIO Set up floppy related fields in 40hardwareInitialize InitOnbaordAUDIO Assign resources to all ISA PnP devices Read HDD boot sector information for Trend Anti-Virus code Enable/Disable Parity Check according to Cmos setupEnable L2 cache Program boot up speed AC2003 Post Code Definition KV8 Pro Appendix H. Troubleshooting Need Assistance? Appendix H User’s Manual Problem Description KV8 Pro OS/Application Hardware Name Brand SpecificationsModel Motherboard Model No How to Get Technical Support Appendix I. How to Get Technical Support Alt.comp.hardware.homebuilt alt.comp.hardware.pc-homebuilt Appendix Fax 43-1-7346713 asguard@asguard.at Thank You Abit Computer Corporation

Abit KV8 PRO user manual

Models: KV8 PRO