Acer 61X Major Chips Description 2-53

Major Chips Description 2-53

Table 2-10 C&T 65550 Pin Descriptions (continued)

Pin# Pin Name Type Description

Flat Panel Display Interface (continued)

55 RSET In Set point resistor for the internal color palette DAC. A 560 Ω

1% resistor is required between RSET and AGND.

59

56 AVCC

AGND VCC

GND Analog power and ground pins for noise isolation for the

internal color palette DAC. AVCC should be isolated from

digital VCC as described in the Functional Description of the

internal color palette DAC. For proper DAC operation, AVCC

should not be greater than IVCC. AGND should be common

with digital ground but must be tightly decoupled to AVCC.

See the Functional Description of the internal color palette

DAC for further information .

203 XTALI (MCLK) In Crystal In. This pin .serves as the input for an external

reference oscillator (usually 14.31818 MHz). Note that in test

mode for the internal clock synthesizer, MCLK is output on

A25 (pin 30) and VCLK is output on A24 (pin

204 (Reserved) Reserved. For compatibility with the 65545, this pin (formerly

"Crystal Out" or "XTLAO") must be disconnected. In addition,

pin 150 must be pulled down on reset. The 65545 no longer

supports the "internal oscillator option.

205

202

206

208

CVCC0

CGND0

CVCCI

CGNDI

VCC

GND

VCC

GND

Analog power and ground pins for noise isolation for the

internal clock synthesizer. Must be the same as VCC for

internal logic. VCC/GND pair 0 and VCC/GND pair 1 pins

must be carefully decoupled individually.

Note that the CVCC voltage must be the same as the voltage

for the internal logic (IVCC).

154 32KHz (GP102) (AA9) In Clock input for refresh of non-self-refresh DRAMs and panel

power sequencing. This pin can be programmed as GP102

instead of 32KHz input, or AA9 for 512Kx3 memory

configurations.

Power / Ground and Standby Control

178 STNDBY# IN Standby Control Pin. Pull this pin to place the chip in

Standby Mode.

80

77

181

184

IVCC

IGND

IVCC

IGND

VCC

GND

VCC

GND

Power / Ground (Internal Logic). 5V±10% or 3.3V±0.3V.

Note that this voltage must be the same as CVCC (voltage for

internal clock synthesizer). This voltage must also be equal

to, or greater than AVCC (voltage for DAC).

9

12

26

42

39

52

BVCC

BGND

BGND

BVCC

BGND

BGND

VCC

GND

GND

VCC

GND

GND

Power / Ground (Bus Interface) 5V±10% or 3.3V±0.3V.

Contents

Main Copyright Disclaimer Purpose Manual Structure Page Conventions Page Table of Contents Chapter 1 System Introduction Chapter 2 Major Chips Description Page Chapter 3 BIOS Setup Information Chapter 4 Disassembly and Unit Replacement Page List of Figures Page Page List of Tables Page Page Page Page 1.1.2 Rear Ports 1.1.3 Indicator Light Page System Introduction 1-5 1.1.4 System Specifications Overview Table 1-3 System Specifications Item Standard Optional 1-6Service Guide Table 1-3 System Specifications (continued) Item Standard Optional Page Page Page Page Page 1.3 Jumpers and Connectors Page 1-14 Service Guide 1.4 Hardware Configuration and Specification 1.4.1 Memory Address Map Table 1-7 Memory Address Map Address Range Definition Function 1.4.2 Interrupt Channel Map Table 1-8 Interrupt Channel Map Priority Interrupt Number Interrupt Source 1.4.4 I/O Address Map Table 1-10 I/O Address Map Address Range Device 1-16 Service Guide 1.4.5 M7101 GPIO (General Purpose I/O) Port Definition Table 1-13 BIOS Specifications Table 1-11 M7101 GPIO Port Definition Item Description 1.4.6 Processor Table 1-12 Processor Specifications Page 1.4.9 Second-Level Cache 1.4.10 Video Memory 1.4.11 Video Page 1.4.12 Parallel Port 1.4.13 Serial Port 1.4.14 Audio 1.4.15 PCMCIA 1.4.16 Touchpad 1.4.17 Keyboard 1-24 Service Guide 1.4.18 FDD Table 1-26 FDD Specifications 1.4.19 HDD Table 1-27 HDD Specifications System Introduction 1-25 1.4.20 CD-ROM Table 1-28 CD-ROM Specifications 1.4.21 Battery Table 1-29 Battery Specifications 1.4.22 Charger 1.4.23 DC-DC Converter 1.4.24 DC-AC Inverter 1-28 Service Guide 1.4.25 LCD Table 1-33 LCD Specifications System Introduction 1-29 1.4.26 AC Adapter Table 1-34 AC Adapter Specifications 1.5 Software Configuration and Specification 1.5.1 BIOS Page Page 1.5.2 Drivers, Applications and Utilities Page 1-38 Service Guide 1.7 Environmental Requirements Table 1-42 Environmental Requirements 1.8 Mechanical Specifications C h a p t e r 2C h a p t e r 2 Major Chips Description 2.1 Major Component List 2.2 ALI M1521 2.2.1 Features Supports all Intel/Cyrix/AMD 586-class processors (with host bus of 66 MHz, 60 MHz and Supports asynchronous/pipeline-burst SRAM Supports FPM/EDO/BEDO/SDRAM DRAMs Page 2.2.2 Block Diagram 2.2.3 System Architecture ALADDIN-III SYSTEM ARCHITECTURE M1521 M1523 GC DRAM 586 CPU 2.2.4 Data Path Figure 2-3 M1521 Data Path E C C M1521 Page 2-8Service Guide 2.2.6 Signal Descriptions Table 2-2 M1521 Signal Descriptions Major Chips Description 2-9 2-10 Service Guide Major Chips Description 2-11 2-12 Service Guide Major Chips Description 2-13 2.3 ALI M1523 2.3.1 Features Technology Provides a bridge between the PCI bus and ISA bus Buffers Page 2-16 Service Guide 2.3.2 Block Diagram Figure 2-5 M1523 Block Diagram M1523 Block Diagram Major Chips Description 2-17 2.3.3 Pin Diagram Figure 2-6 M1523 Pin Diagram ALi M1523 2-18 Service Guide 2.3.4 Signal Descriptions Table 2-3 M1523 Signal Descriptions Major Chips Description 2-19 2-20 Service Guide Major Chips Description 2-21 2-22 Service Guide Major Chips Description 2-23 Page Major Chips Description 2-25 2.4.2 Pin Diagram Figure 2-7 M7101 Pin Diagram ALi M7101 2-26 Service Guide 2.4.3 Pin Description Table 2-4 M7101 Pin Descriptions Major Chips Description 2-27 2-28 Service Guide Major Chips Description 2-29 2-30 Service Guide Major Chips Description 2-31 2-32 Service Guide Major Chips Description 2-33 2.4.4 Different Pin definition setting SLED, CCFT, DISPLAY, SPKCTL, SQWO and GPIOC2 pins are all internal pull high 50K Pull high : GPIOA0, GPIOA4, GPIOB1, GPIOB3, GPIOB6, GPIOB7, GPIOC1, GPIOC2, Pull low : Other GPIO pins. 2-36 Service Guide 2.4.5 Numerical Pin List Table 2-7 M7101 Numerical Pin List No. Pin Name Type No. Pin Name Type Major Chips Description 2-37 2.4.6 Alphabetical Pin List Table 2-8 M7101 Alphabetical Pin List No. Pin Name Type No. Pin Name Type 2.4.7 Function Description Major Chips Description 2-39 Table 2-9 M7101 PCI Interface Lock Register Action I/O Port 0178h/0078h I/O Port 017Ah/007Ah Figure 2-8 State Machine for PCI Interface State Machine for PCI Interface. 2.5 C&T 65550 High Performance Flat Panel/CRT VGA Controller 2.5.1 Features Page Page Major Chips Description 2-43 2.5.4 Pin Descriptions Table 2-10 C&T 65550 Pin Descriptions 2-44 Service Guide Major Chips Description 2-45 2-46 Service Guide Major Chips Description 2-47 2-48 Service Guide Major Chips Description 2-49 2-50 Service Guide Major Chips Description 2-51 2-52 Service Guide Major Chips Description 2-53 2-54 Service Guide Table 2-11 Flat Panel Display Interface Configurations Page 2.6 TI PCI1131 CardBus Controller 2.6.1 Overview Page Page Page Page Page Page Major Chips Description 2-63 2.6.6 Terminal Functions NAME NO. Table 2-13 PCI1131 Pin Descriptions 2-64 Service Guide NAME NO. Page 2-66 Service Guide A+ B Major Chips Description 2-67 A+ B 2-68 Service Guide A+ B Major Chips Description 2-69 A+ B 2-70 Service Guide A+ B Major Chips Description 2-71 A+ B Page Major Chips Description 2-73 TERMINAL NAME NO I /O TYPE FUNCTION 2-74 Service Guide Table 2-13 PCI1131 Pin Descriptions (Continued) TERMINAL NAME NO I /O TYPE FUNCTION 2.7 NS87336VJG Super I/O Controller 2.7.1 Features 100% compatible with ISA, and EISA architectures The Floppy Disk Controller: The Bidirectional Parallel Port: The UARTs: The Address Decoder Enhanced Power Management Mixed Voltage support Plug and Play Compatible: Figure 2-15 NS87336VJG Block Diagram 100-Pin TQFP package - PC87336VJG 2.7.2 Block Diagram Page Major Chips Description 2-79 2.7.4 Pin Description Table 2-14 NS87336VJG Pin Descriptions 2-80 Service Guide Major Chips Description 2-81 2-82 Service Guide Major Chips Description 2-83 2-84 Service Guide Major Chips Description 2-85 2-86 Service Guide Page Page Major Chips Description 2-89 2.8.3 Pin Descriptions Table 2-15 YMF715 Descriptions Pin name Pins I/O Type Size Function 2-90 Service Guide Table 2-15 YMF715 Descriptions (Continued) Pin name Pins I/O Type Size Function Multi-purpose Dins: 13 pins Page Providing low battery warning signals when the system using battery as the main power 2.9.3 Absolute Maximum Ratings 2.9.4 Electrical Characteristics Major Chips Description 2-93 2.9.5 Pin Diagram Major Chips Description 2-95 2.9.6 Pin Description Table 2-18 T62.062.C Pin Description table Item Pin Name I/O Description 2.9.7 Functions Description Page 2.10 T62.061.C DC-DC Converter 2.10.1 Pin Diagram 2.10.2 Pin Assignment Page +2.35V:(2.45V) Load : 0A-4.2A Regulation: +5%, -4% +12V : Load : 0A-0.15A Regulation: +/-5% +6V : Load : 0A~0.1A Regulation: 5.5V~7.5V 5VSB:Load : 5mA Regulation:+/-10% 2.10.4 Control Page 2.11 T62.064.C DC-AC Inverter (11.3") 2.11.1 Electrical Specifications 2.11.2 Pin & Connector Assignment Page 2.12 T62.066.C DC-AC Inverter (12.1") 2.12.1 Electrical Specifications 2.12.2 Pin & Connector Assignment Page C h a p t e r 3C h a p t e r 3 BIOS Setup Information Page Page 3.3 Basic System Configuration 3.3.1 Date and Time 3.3.2 Floppy Disk Drives 3.3.3 Hard Disk Drive 3.3.4 Large Hard Disk Capacity 3.3.5 Memory Test [Disabled] 3.3.6 Boot Display 3.3.7 Quiet Boot 3.4 System Security 3.4.1 Floppy Disk Drive Control 3.4.2 Hard Disk Drive Control 3.4.3 System Boot Drive Control 3.4.4 CD-ROM Bootable Page Capabilities Port(ECP)] . The default value, with ECP selected, is [0] 3.4.8 Passwords 3.4.9 CardBus Support 3.5 Power Management Settings 3.5.1 Power Management Mode [Disabled] to turn off all the timers. The default setting is [Enabled] 3.5.2 Display Standby Timer 3.5.3 Hard Disk Standby Timer 3.5.4 System Sleep Timer 3.5.5 System Sleep Mode 3.5.6 System Resume Timer Mode 3.5.7 System Resume Date and Time 3.5.8 Modem Ring Resume On Indicator Page 3.6 System Information Reference Page 3.7 Load Setup Default Settings C hC h a p t a p t e r 4 e r 4 Disassembly and Unit Replacement 4.1 General Information 4.1.1 Before You Begin 4.1.2 Connector Types Connectors with no locks Connectors with locks Unplugging the Cable Plugging the Cable 4.1.3 Disassembly Sequence Page 4.2 Replacing Memory 4.3 Removing the Hard Disk Drive Page Page Page Page 4.5.3 Replacing the CPU Page Page Page Page Page Page Page Page Page 4.6 Disassembling the Display Page Page Page A p A p p e n d p e n d i x Ai x A Model Number Definition Model Number Definition A-1 Memory and Battery Page Page Page Page A p A p p e n d p e n d i x Ci x C Spare Parts Spare Parts C-1 This appendix lists the spare parts of the notebook TI EXTENSA 610. Table C-1 Spare Parts List C-2Service Guide Table C1 Spare parts list (continued) Spare Parts C-3 Table C1 Spare parts list (continued) Page Page Page Page P55C/P54C CPU BUS & CACHE PCI & DRAM PCI-ISA BRIDGE & IDE M1523 Page Page ## REMOVE R65,R178,R182,R181,R66 PAD Page ## REMOVE U53 PAD TRACKSTICK CONN KB BD CONN. Page ## CIRCUIT MODIFY Page Page Page Page Page Page Page Page Page Page Page ALADDIN III COMMON POWER: VCC_IDE & GND CPU BYPASS CAPACITORS CACHE M1523 A p A p p e n d p e n d i x Ei x E BIOS POST Checkpoints BIOS POST Checkpoints E-1 This appendix lists the POST checkpoints of the notebook BIOS. Table E-1 POST Checkpoint List E-2Service Guide Table E-1 POST Checkpoint List (Continued) BIOS POST Checkpoints E-3 Table E-1 POST Checkpoint List (Continued) Checkpoint Description